Bug Reports

• Some layers of the model are always compressed

  84 views 9 comments 0 points Most recent by Repetier November 2016
• X Y coord error after G29

  53 views 2 comments 0 points Most recent by MartinH November 2016
• Repetier doesn't start after unplugging second screen.

  41 views 2 comments 0 points Most recent by spiderdab November 2016
• Printfilling issues

  44 views 3 comments 0 points Most recent by Repetier October 2016
• High consumtiom of mem.

  29 views 1 comment 0 points Most recent by Repetier October 2016
• Prints freeze

  102 views 5 comments 0 points Most recent by Repetier October 2016
• Unable to access eeprom configuration....

  408 views 3 comments 0 points Most recent by Repetier October 2016
• The estimated time in repetier shows up negative

  353 views 13 comments 0 points Most recent by Repetier August 2016
• Print Panel coordinates doubling when manual moving. Mac V 1.011

  85 views 3 comments 0 points Most recent by Gordy August 2016
• GUI coordinates not updating after G92 and M114 (V1.6.2)

  97 views 1 comment 0 points Most recent by Repetier August 2016
• Unable to open Printer properties

  35 views 1 comment 0 points Most recent by Repetier August 2016
• Printer pauses for several seconds when printing curves, leaving behind a zit.

  106 views 4 comments 0 points Most recent by Repetier July 2016
• No Extruder Output

  254 views 2 comments 0 points Most recent by Jan July 2016
• Bed Height Map Crashes after few probes.

  155 views 1 comment 0 points Most recent by Repetier June 2016
• Crash when userBased set to fals

  80 views 3 comments 0 points Most recent by Repetier June 2016
• [Linux V1.5.6] Save to Server Bug

  222 views 6 comments 0 points Most recent by foxpup April 2016
• some minor bugs

  151 views 6 comments 0 points Most recent by juulius April 2016
• original RAMPS-FD D10, D11 outputs problem

  111 views 0 comments 0 points Started by Gudrimelis March 2016
• Can't recover from hanging printer

  108 views 1 comment 0 points Most recent by Repetier March 2016
• SD card removal under filament change

  75 views 0 comments 0 points Started by marcoleo February 2016
• Crash editing Printer name in Repetier-Host 1.6.1

  211 views 1 comment 0 points Most recent by Repetier February 2016
• Zmax move back after homing not working.

  145 views 1 comment 0 points Most recent by Repetier February 2016
• Z Axis homing fails to come back down sometimes

  287 views 11 comments 0 points Most recent by Jeff_T January 2016
• Can't send G-code Repetier-Host Mac

  795 views 5 comments 0 points Most recent by Repetier January 2016
• Incorrect temps displayed in dual temp configurations

  107 views 3 comments 0 points Most recent by Repetier January 2016
• [1.6.0, Delta printer, Windows] Bed height map issues

  199 views 5 comments 0 points Most recent by docpayce January 2016
• [1.6.0] CuraEngine Inner Perimeter Speed Bug

  131 views 1 comment 0 points Most recent by Repetier December 2015
• Bluetooth serial port

  587 views 1 comment 0 points Most recent by Repetier November 2015
• Extruder Offset measured in wrong unit

  893 views 3 comments 0 points Most recent by Repetier November 2015
• Crash of repetier host because of SD card

  393 views 2 comments 0 points Most recent by jellehak November 2015