Bug Reports

• Repetier need a lot of improofments for example...

  1 view 2 comments 0 points Most recent by RAyWB August 30
• Error:er cooler speed [0-255]

  25 views 22 comments 0 points Most recent by Other_Dave August 25
• 2.1.4 Host - SCRIPTS buttons are not acting correctly.

  1 view 3 comments 0 points Most recent by Repetier July 28
• offset

  1 view 10 comments 0 points Most recent by Repetier June 3
• RepetierHost 2.1.3 crashes when attempting to import to more than 2 STLs simultanously

  1 view 1 comment 0 points Most recent by Repetier May 8
• Cant get extruder to rise in temp.

  1 view 3 comments 0 points Most recent by Repetier April 2
• I can't use G203 command , it return Unknown command

  1 view 1 comment 0 points Most recent by Repetier March 20
• Eigenartige Zeitwerte im Jobstatus

  1 view 4 comments 0 points Most recent by Repetier March 12
• DualX: extruder only moves in one direction (offset)

  1 view 5 comments 0 points Most recent by Repetier February 11
• Erros ao conectar o repetier

  1 view 1 comment 0 points Most recent by ShadowBrother February 7
• Repetier Informer IOS

  1 view 3 comments 0 points Most recent by Repetier November 2018
• Two IP addresses necessary?

  1 view 2 comments 0 points Most recent by Repetier November 2018
• alarm state

  1 view 1 comment 0 points Most recent by Repetier November 2018
• Repetier server crashes at the end of the prints

  1 view 5 comments 0 points Most recent by Repetier November 2018
• M117 messes up next G-code line

  1 view 2 comments 0 points Most recent by robbertkl November 2018
• Druckjob stoppt, Druckauftrag erscheint in der Warteschlange

  1 view 4 comments 0 points Most recent by Repetier October 2018
• 2 In 1 Out Hotend Configuration Cannot unpause when Jam detected

  1 view 1 comment 0 points Most recent by Repetier October 2018
• Error reading STL file

  1 view 1 comment 0 points Most recent by Culturedropout September 2018
• Repetier Host 2.1.3 manual control not retaining g92 information

  1 view 1 comment 0 points Most recent by Repetier September 2018
• Slic3r PE cost is always 0

  1 view 3 comments 0 points Most recent by Repetier September 2018
• 3D View is empty

  1 view 5 comments 0 points Most recent by rotceh_dnih September 2018
• Error: Repetier-Host after click on Load for Gcode witn double dot ( : ) sign in name on Server tab

  1 view 1 comment 0 points Most recent by Repetier September 2018
• Extruder stops during print (Repetier 1.0.2)

  1 view 3 comments 0 points Most recent by Repetier August 2018
• Perimeter before Infill does not work on Cura Engine

  1 view 1 comment 0 points Most recent by dschoni August 2018
• DimaZikov

  1 view 3 comments 0 points Most recent by Repetier August 2018
• Object on "Ex2" only generates gcode for 1st extruder (misses T1)

  1 view 2 comments 0 points Most recent by warrendlr August 2018
• Repetier Host does not start anymore on Ubuntu 16.04

  1 view 4 comments 0 points Most recent by Repetier August 2018
• Uploading gcode to repetier server freezes UI of RH

  1 view 2 comments 0 points Most recent by guffy August 2018
• Not displaying filament line after retraction

  1 view 1 comment 0 points Most recent by Repetier August 2018
• Nach Update auf 0.90.4 kein Datei Upload mehr möglich !!!

  1 view 5 comments 0 points Most recent by Repetier August 2018