Bug Reports

• 2nd extruder moves also X

  179 views 6 comments 0 points Most recent by fra87 November 2015
• Printer Area Height and Depth are switched

  79 views 1 comment 0 points Most recent by Repetier November 2015
• ZLift with Firware Retraction bug

  180 views 7 comments 0 points Most recent by jbainesy November 2015
• Extruder temperature unreliable

  137 views 1 comment 0 points Most recent by Repetier October 2015
• RH 1.5.6 refuses to park after job.

  66 views 3 comments 0 points Most recent by Stoutlimb October 2015
• RepetierHost 1.5.6 and Slic3r 1.2.9 incompatibility

  170 views 1 comment 0 points Most recent by twforeman October 2015
• Printer becomes unresponsive when print is initialized

  157 views 2 comments 0 points Most recent by cjkmiec October 2015
• Bed height map creation unwanted Z move on Z-probe error

  197 views 0 comments 0 points Started by furynick October 2015
• Object preview is off the platter (actual print is fine)

  96 views 1 comment 0 points Most recent by Repetier October 2015
• M21 Crashes Host

  264 views 9 comments 0 points Most recent by Repetier September 2015
• Repetier 1.5.5 (and maybe earlier) Double click on Connect button

  170 views 1 comment 0 points Most recent by Repetier September 2015
• Repetier Server "stops" printing, motors off, temperatures maintained.

  357 views 3 comments 0 points Most recent by Repetier September 2015
• Resend:

  473 views 2 comments 0 points Most recent by davistanford September 2015
• Rep Host 1.5.0 & 1.5.4 fail to read temps

  275 views 3 comments 0 points Most recent by LouGeezer August 2015
• Manual Control Z-Min bug

  500 views 4 comments 0 points Most recent by Couri August 2015
• Repetier Host 1.5.4 'Start Code' script runs at end, too

  220 views 2 comments 0 points Most recent by Repetier August 2015
• Repetier-Host 1.5.2 and 1.5.4 crashes

  364 views 1 comment 0 points Most recent by Repetier August 2015
• Virtualprinter too Slow

  214 views 2 comments 0 points Most recent by Neri August 2015
• Show Travel Moves

  209 views 0 comments 0 points Started by clefranc July 2015
• If you accidentaly click disconnect during a print, there is no cancel button.

  214 views 1 comment 0 points Most recent by Repetier July 2015
• Repetier-Server connector not available

  320 views 3 comments 0 points Most recent by Repetier July 2015
• Repetier-Host 1.0.6 / Linux

  158 views 1 comment 0 points Most recent by Repetier June 2015
• Repetier-Host stall printing with large G-code

  251 views 1 comment 0 points Most recent by Repetier May 2015
• Host 1.0.5 Go to Park Position After Job/Kill Does Not

  950 views 7 comments 0 points Most recent by theonteg May 2015
• Crash in preview when right-clicking

  521 views 14 comments 0 points Most recent by larsen April 2015
• Volumetric E and used Filament

  575 views 3 comments 0 points Most recent by Repetier April 2015
• Virtual extruders bug

  137 views 4 comments 0 points Most recent by Repetier April 2015
• Repetier-Host Mac 0.56 Can't Delete Printer Configuration

  614 views 1 comment 0 points Most recent by Repetier March 2015
• Unnecessary Travel When Printing Circles

  383 views 2 comments 0 points Most recent by LordFly March 2015
• EXT0_EXTRUDER_COOLER_SPEED has no effect on FAN speed

  676 views 1 comment 0 points Most recent by Repetier March 2015