Bug Reports

• Object preview is off the platter (actual print is fine)

  96 views 1 comment 0 points Most recent by Repetier October 2015
• M21 Crashes Host

  264 views 9 comments 0 points Most recent by Repetier September 2015
• Repetier 1.5.5 (and maybe earlier) Double click on Connect button

  170 views 1 comment 0 points Most recent by Repetier September 2015
• Repetier Server "stops" printing, motors off, temperatures maintained.

  357 views 3 comments 0 points Most recent by Repetier September 2015
• Resend:

  473 views 2 comments 0 points Most recent by davistanford September 2015
• Rep Host 1.5.0 & 1.5.4 fail to read temps

  275 views 3 comments 0 points Most recent by LouGeezer August 2015
• Manual Control Z-Min bug

  500 views 4 comments 0 points Most recent by Couri August 2015
• Repetier Host 1.5.4 'Start Code' script runs at end, too

  220 views 2 comments 0 points Most recent by Repetier August 2015
• Repetier-Host 1.5.2 and 1.5.4 crashes

  364 views 1 comment 0 points Most recent by Repetier August 2015
• Virtualprinter too Slow

  214 views 2 comments 0 points Most recent by Neri August 2015
• Show Travel Moves

  209 views 0 comments 0 points Started by clefranc July 2015
• If you accidentaly click disconnect during a print, there is no cancel button.

  214 views 1 comment 0 points Most recent by Repetier July 2015
• Repetier-Server connector not available

  320 views 3 comments 0 points Most recent by Repetier July 2015
• Repetier-Host 1.0.6 / Linux

  158 views 1 comment 0 points Most recent by Repetier June 2015
• Repetier-Host stall printing with large G-code

  251 views 1 comment 0 points Most recent by Repetier May 2015
• Host 1.0.5 Go to Park Position After Job/Kill Does Not

  950 views 7 comments 0 points Most recent by theonteg May 2015
• Crash in preview when right-clicking

  521 views 14 comments 0 points Most recent by larsen April 2015
• Volumetric E and used Filament

  575 views 3 comments 0 points Most recent by Repetier April 2015
• Virtual extruders bug

  137 views 4 comments 0 points Most recent by Repetier April 2015
• Repetier-Host Mac 0.56 Can't Delete Printer Configuration

  614 views 1 comment 0 points Most recent by Repetier March 2015
• Unnecessary Travel When Printing Circles

  383 views 2 comments 0 points Most recent by LordFly March 2015
• EXT0_EXTRUDER_COOLER_SPEED has no effect on FAN speed

  676 views 1 comment 0 points Most recent by Repetier March 2015
• Out of Video memory / Exception while drawing

  4.2K views 9 comments 0 points Most recent by 3D_4Ever February 2015
• I cannot choose the installation language

  299 views 2 comments 0 points Most recent by 3D_4Ever February 2015
• Upload to sd card not working and starts a print automatically.

  806 views 0 comments 0 points Started by netbear January 2015
• Repetier is permanently frozen

  329 views 3 comments 0 points Most recent by Repetier January 2015
• Repetier-Host 1.0.6 is not working anymore with Slic3r 1.2.2 and later

  523 views 1 comment 0 points Most recent by Repetier January 2015
• Repetier on Ubuntu - manual controls: graphics truncated, can't see all xyz and extrude buttons

  152 views 2 comments 0 points Most recent by rkmutter December 2014
• Printing registration bug

  471 views 11 comments 0 points Most recent by skutch December 2014
• "SD Card" Tab

  213 views 2 comments 0 points Most recent by Coelestinian November 2014