Bug Reports

• errore arduino su collegamento anycubik 4 max pro

  1 view 0 comments 0 points Started by paolocbr April 2020
• G28 command broken

  1 view 2 comments 0 points Most recent by santy3d April 2020
• Communication timeout : reset send buffer block

  1 view 4 comments 0 points Most recent by Repetier April 2020
• Temperatur extruder 2 steht fest auf 100° / Temperatur extruder 2 frozen

  1 view 10 comments 0 points Most recent by Repetier April 2020
• Host will not reopen after closing

  1 view 3 comments 0 points Most recent by Repetier April 2020
• Repetier Host CuraEngine Slice Bug found

  1 view 1 comment 0 points Most recent by Repetier April 2020
• 3d View is Empty (new issue)

  1 view 3 comments 0 points Most recent by Repetier April 2020
• Error when slicing with PrusaSlicer 2.2.0

  1 view 1 comment 0 points Most recent by Repetier April 2020
• Repetier Host is unable to install

  1 view 1 comment 0 points Most recent by Repetier March 2020
• M117 messes up next G-code line

  1 view 4 comments 0 points Most recent by Repetier March 2020
• Mintemp triggered

  1 view 2 comments 0 points Most recent by Repetier February 2020
• Server bricht mitten im Druck ab

  1 view 17 comments 0 points Most recent by Repetier December 2019
• problem with bluetooth serial

  1 view 10 comments 0 points Most recent by Repetier November 2019
• RH @pause doesn't work

  1 view 1 comment 0 points Most recent by Repetier October 2019
• Repetier need a lot of improofments for example...

  1 view 2 comments 0 points Most recent by RAyWB August 2019
• Error:er cooler speed [0-255]

  25 views 22 comments 0 points Most recent by Other_Dave August 2019
• 2.1.4 Host - SCRIPTS buttons are not acting correctly.

  1 view 3 comments 0 points Most recent by Repetier July 2019
• offset

  1 view 11 comments 0 points Most recent by Repetier June 2019
• RepetierHost 2.1.3 crashes when attempting to import to more than 2 STLs simultanously

  1 view 1 comment 0 points Most recent by Repetier May 2019
• Cant get extruder to rise in temp.

  1 view 3 comments 0 points Most recent by Repetier April 2019
• I can't use G203 command , it return Unknown command

  1 view 1 comment 0 points Most recent by Repetier March 2019
• Eigenartige Zeitwerte im Jobstatus

  1 view 4 comments 0 points Most recent by Repetier March 2019
• DualX: extruder only moves in one direction (offset)

  1 view 5 comments 0 points Most recent by Repetier February 2019
• Erros ao conectar o repetier

  1 view 1 comment 0 points Most recent by ShadowBrother February 2019
• Repetier Informer IOS

  1 view 3 comments 0 points Most recent by Repetier November 2018
• Two IP addresses necessary?

  1 view 2 comments 0 points Most recent by Repetier November 2018
• alarm state

  1 view 1 comment 0 points Most recent by Repetier November 2018
• Repetier server crashes at the end of the prints

  1 view 5 comments 0 points Most recent by Repetier November 2018
• 2 In 1 Out Hotend Configuration Cannot unpause when Jam detected

  1 view 1 comment 0 points Most recent by Repetier October 2018
• Error reading STL file

  1 view 1 comment 0 points Most recent by Culturedropout September 2018