General

• How to add 2nd heat bed control?

  1 view 1 comment 0 points Most recent by Repetier January 2018
• Want to donate directly through Credit card

  1 view 1 comment 0 points Most recent by Repetier January 2018
• E0 Temp ?

  1 view 16 comments 0 points Most recent by Repetier January 2018
• Compiling / Free Memory

  1 view 1 comment 0 points Most recent by Repetier January 2018
• Thermocouple

  1 view 3 comments 0 points Most recent by Repetier January 2018
• eeprom ?

  1 view 10 comments 0 points Most recent by gorf25 December 2017
• 4.9K thermistor ? on Diamond hot end

  1 view 1 comment 0 points Most recent by recoush December 2017
• Autobedleveling only works when Arduino is Reset

  1 view 3 comments 0 points Most recent by Repetier December 2017
• Move UP 40mm before homing

  1 view 2 comments 0 points Most recent by Tomu December 2017
• Dynamically setting delta calibration parameters

  1 view 4 comments 0 points Most recent by Repetier November 2017
• Does changed made with M206 are assumed during print?

  1 view 4 comments 0 points Most recent by Nandox7 November 2017
• extruder temp shows "def"

  12 views 1 comment 0 points Most recent by Repetier November 2017
• Everything slows down when X axis changes direction.

  35 views 6 comments 0 points Most recent by geofox784 November 2017
• PWM case light

  29 views 2 comments 0 points Most recent by Anteino November 2017
• Questions regarding Z endstops, probing, and a possible bug

  43 views 3 comments 0 points Most recent by Repetier October 2017
• Calibrating CoreXY

  442 views 13 comments 0 points Most recent by geoffreyforest October 2017
• Ramps 1.4 thermistor pcb repair

  26 views 4 comments 0 points Most recent by recoush October 2017
• Warning: Communication timeout - resetting communication buffer.

  413 views 3 comments 0 points Most recent by Repetier October 2017
• Choppy printing Delta

  80 views 9 comments 0 points Most recent by Repetier October 2017
• Max. z-probe - bed dist.

  20 views 2 comments 0 points Most recent by novio8 October 2017
• Probe accuracy test

  20 views 1 comment 0 points Most recent by Repetier October 2017
• Two Y_min stops and homing the extruder

  22 views 2 comments 0 points Most recent by Anteino October 2017
• Delta G32 S2

  88 views 9 comments 0 points Most recent by novio8 October 2017
• print.job stops randomly even with sd card printing and logs don't help much

  22 views 1 comment 0 points Most recent by Repetier September 2017
• baud rates cant change

  33 views 5 comments 0 points Most recent by recoush September 2017
• running from sd card

  29 views 2 comments 0 points Most recent by recoush September 2017
• Expanding fans on radds for part cooling.. Can it be done with repetier firmware?

  32 views 3 comments 0 points Most recent by Repetier September 2017
• Two Heater blocks in one hot end

  29 views 1 comment 0 points Most recent by Repetier September 2017
• EEprom values don't get updated when flashing new firmware

  131 views 5 comments 0 points Most recent by kina September 2017
• Install Z-Probing WITHOUT a Z Max end switch?

  86 views 9 comments 0 points Most recent by BernieG August 2017