General

• Dual Motor Y-Axis homing problem

  1 view 7 comments 0 points Most recent by dominik_00br September 2018
• Set Up for Prusa i3 MK2

  52 views 1 comment 0 points Most recent by raelbsd September 2018
• SLS 3D printer: Convert Old Set up top CoreXY issue

  1 view 2 comments 0 points Most recent by Repetier August 2018
• Unable to compile repetier firmware in arduino

  1 view 0 comments 0 points Started by adamhaze8 August 2018
• Z offset not working in ver101 will not go below zero

  1 view 4 comments 0 points Most recent by bustenchops August 2018
• Auto bed leveling

  1 view 6 comments 0 points Most recent by Tinchus2009 August 2018
• DIOORIG_FAN2_PIN_WPORT' was not declared in this scope

  1 view 1 comment 0 points Most recent by Repetier July 2018
• sd card read error

  1 view 7 comments 0 points Most recent by rubanaero July 2018
• Dual extruder setup - x2 motor thinks home is (0,0)

  1 view 1 comment 0 points Most recent by Repetier July 2018
• Which are the variables involved in determine the Origin and Home

  1 view 1 comment 0 points Most recent by Repetier July 2018
• Yet another Z-Probe Problem

  1 view 8 comments 0 points Most recent by mcescher July 2018
• Anet A8 ( Melzi ) v1 firmware problem

  1 view 6 comments 0 points Most recent by Tomu June 2018
• Firmware Repetier auf Anet A6

  1 view 2 comments 0 points Most recent by Tomu June 2018
• Anet A8 Firmware 0.92.9 Ready to use solution

  1 view 0 comments 0 points Started by Tomu June 2018
• Zprobe height not working

  1 view 3 comments 0 points Most recent by Repetier June 2018
• G28 + Z Endstop min

  1 view 2 comments 0 points Most recent by mtmello2003 June 2018
• Why would both thermistors report an exact same negative reading?

  1 view 3 comments 0 points Most recent by Repetier May 2018
• bltouch clone , delta printer, z-min end-stop trigger

  1 view 5 comments 0 points Most recent by yodor May 2018
• Compilation error 'DIOORIG_E2_DIR_PIN_DDR' (Ramps 1.4)

  1 view 1 comment 0 points Most recent by frguy May 2018
• Delta calibration issues

  1 view 6 comments 0 points Most recent by hen3bosch May 2018
• Measure Distortion doesn't end!

  1 view 6 comments 0 points Most recent by Repetier May 2018
• Z-Homing einstellen

  1 view 2 comments 0 points Most recent by Buttons May 2018
• G30

  1 view 34 comments 0 points Most recent by Repetier March 2018
• Homing error with Z probe

  1 view 1 comment 0 points Most recent by MartinH February 2018
• ultratronics pro v1 sd card

  1 view 1 comment 0 points Most recent by Repetier February 2018
• Problem Achs Konfiguration

  1 view 3 comments 0 points Most recent by Repetier January 2018
• Problem Achs Konfiguration

  1 view 0 comments 0 points Started by DerHimbeerHugo January 2018
• Factory Installed 0.92.8 - how to activate autolevel

  1 view 0 comments 0 points Started by vader7071 January 2018
• Prusa i3 - MKS Gen-2Z V1.2

  1 view 0 comments 0 points Started by luk1990 January 2018
• Extruder pauses during perimeter/infill

  1 view 2 comments 0 points Most recent by Repetier January 2018