General

• Prusa MMU 2.0 in Repetier?

  1 view 6 comments 0 points Most recent by LewisH95 December 2019
• What are the printer size limitations for Delta style printers

  1 view 5 comments 0 points Most recent by Repetier December 2019
• Bed leveling issue

  1 view 3 comments 0 points Most recent by LewisH95 December 2019
• 1.0.2 not working on my Mega 2560 and RAMPS.

  1 view 33 comments 0 points Most recent by Repetier December 2019
• Changing the XY Locations used during Z Probing

  1 view 2 comments 0 points Most recent by jvbiondo December 2019
• version 1.0.4dev

  1 view 3 comments 0 points Most recent by Repetier December 2019
• "Error compiling for board Sanguino"

  1 view 13 comments 0 points Most recent by Repetier November 2019
• Installing Repetier on Da Vinci 1.0 Jr

  1 view 1 comment 0 points Most recent by Laseracid October 2019
• Firmware compilation mile-long errors

  1 view 2 comments 0 points Most recent by speedy_rudolf October 2019
• Serious problems with FW compiling by Arduino IDE

  1 view 6 comments 0 points Most recent by flyover1974 September 2019
• DUE/RADDS with ATX power supply cycles on/off continuously when not plugged into USB

  1 view 3 comments 0 points Most recent by Repetier September 2019
• Moving extruder to different position after homing

  1 view 3 comments 0 points Most recent by rincewind August 2019
• M206 (v. 0.91)

  1 view 2 comments 0 points Most recent by Repetier August 2019
• firmware configuration disabled

  1 view 6 comments 0 points Most recent by tomasby August 2019
• Timelapse flash

  1 view 2 comments 0 points Most recent by Seyuho July 2019
• fan PWM frequency

  713 views 33 comments 0 points Most recent by elidor June 2019
• Z_PROBE_DELAY ?

  1 view 1 comment 0 points Most recent by leadinglights June 2019
• Cartesian - Homing ignores limit switches after G32

  1 view 1 comment 0 points Most recent by Repetier June 2019
• Homing fails every other time G28 is entered

  1 view 2 comments 0 points Most recent by jvbiondo June 2019
• Bad value for Z counter, after G28

  1 view 13 comments 0 points Most recent by Repetier May 2019
• Wanted: constant movement during linear movement with G1 and G0 sequences

  1 view 2 comments 0 points Most recent by Domingo April 2019
• Fan setting and control

  375 views 12 comments 0 points Most recent by Repetier April 2019
• Need to setup dual extrusion in ramps 1.4 board

  1 view 1 comment 0 points Most recent by Repetier April 2019
• BL Touch Power? (Large format setup, similar to Sparkcube v1.1XL)

  1 view 2 comments 0 points Most recent by opy01 April 2019
• Z Sensors

  1 view 32 comments 0 points Most recent by Tanuki44 April 2019
• Z probe rises 20mm between the probes (G32 & G33)

  1 view 2 comments 0 points Most recent by ecj April 2019
• laser on too early

  1 view 10 comments 0 points Most recent by Jerome March 2019
• Understanding laser

  1 view 1 comment 0 points Most recent by Repetier March 2019
• Delta Display

  1 view 2 comments 0 points Most recent by novio8 March 2019
• Low Memory

  1 view 3 comments 0 points Most recent by Repetier March 2019