General

• Where can I adjust steps per mm for the extruder?

  47 views 1 comment 0 points Most recent by MartinH August 2017
• Is my 5A polyfuse on my RAMPS board bad?

  19 views 0 comments 0 points Started by mitch25 August 2017
• ANet A8 Config File

  327 views 1 comment 0 points Most recent by BernieG August 2017
• Custom pause behaviour

  52 views 3 comments 0 points Most recent by Repetier August 2017
• A third thermistor?

  31 views 2 comments 0 points Most recent by RGN01 July 2017
• Z-probing - G32 keeps crashing into x and y endstops

  42 views 1 comment 0 points Most recent by rhklein July 2017
• Implementing G-code procedures in the firmware

  126 views 5 comments 0 points Most recent by Anteino July 2017
• Servo and microswitch bed leveling

  24 views 1 comment 0 points Most recent by Repetier July 2017
• PWM Caselight

  35 views 1 comment 0 points Most recent by Repetier July 2017
• Clearing NAN with M-codes?

  44 views 2 comments 0 points Most recent by wildcardfox June 2017
• looking for someone with a geetech G2S or other delta that has this firmware working

  156 views 24 comments 0 points Most recent by Repetier June 2017
• Plotter(=Laser) problem with output for pen control

  127 views 15 comments 0 points Most recent by Repetier June 2017
• can somone tell me what is going wrong with my abl setup ?

  41 views 1 comment 0 points Most recent by Leitz June 2017
• Where is the firmware.

  71 views 1 comment 0 points Most recent by Rossini May 2017
• Autolevel issues

  125 views 16 comments 0 points Most recent by Repetier May 2017
• G33 problem

  129 views 17 comments 0 points Most recent by Repetier May 2017
• Replace Zmin endstop by Z probe

  137 views 8 comments 0 points Most recent by Ben3D May 2017
• Formula given for Z-Probe calibration seems wrong

  51 views 1 comment 0 points Most recent by Repetier May 2017
• Manual lowering of hotend

  40 views 3 comments 0 points Most recent by Repetier May 2017
• Fan does not automatically turn on

  91 views 2 comments 0 points Most recent by cnagy May 2017
• prints come out mirrored form start

  28 views 2 comments 0 points Most recent by gassiebernal May 2017
• X Axis Jerks when Y axis Moves - Motor Current/ Jerk Settings?

  83 views 0 comments 0 points Started by aalexa5588 April 2017
• Plasma post processing

  40 views 0 comments 0 points Started by chrisbt April 2017
• Delta "un calibrates" during print

  49 views 4 comments 0 points Most recent by Sewyboowy April 2017
• CoreXY 'Microcube' Printer, Z drops

  63 views 4 comments 0 points Most recent by Repetier April 2017
• M109 Command not working

  84 views 6 comments 0 points Most recent by NerdHerd704 April 2017
• How to calibrate the display encoder?

  128 views 4 comments 0 points Most recent by icefire April 2017
• Cannot get my inductive probe to work with Repetier FW.. please help!

  70 views 3 comments 0 points Most recent by icefire March 2017
• Repetier running Robotic Arm !!!

  65 views 6 comments 0 points Most recent by robbycandra March 2017
• Problems with auto bed leveling on Wanhao i3

  247 views 18 comments 0 points Most recent by bryanmaple March 2017