Toggle navigation
Categories
Discussions
About Us
Privacy Policy
Sign In
Home
›
Repetier-Firmware
›
General
General
«
1
…
5
6
7
8
9
10
11
…
17
»
tilting with servo
54
views
2
comments
0
points
Most recent by
Tanuki44
March 2017
Delta printer pauses constantly
40
views
2
comments
0
points
Most recent by
Repetier
March 2017
Automatically start print
51
views
2
comments
0
points
Most recent by
3feet
March 2017
Firmware stop / reset under Auto leveling
87
views
7
comments
0
points
Most recent by
kina
March 2017
SD reader does not work
88
views
5
comments
0
points
Most recent by
Repetier
March 2017
Bed Thermistor
75
views
3
comments
0
points
Most recent by
Repetier
March 2017
Z-Probing Instructions?
623
views
21
comments
0
points
Most recent by
cinematographer
March 2017
Protect hardware from autoleveling sensor malfunction - keep Z-min endstop 2 mm below print surface
109
views
6
comments
0
points
Most recent by
good_idea
March 2017
Fan on D9 setup help
130
views
3
comments
0
points
Most recent by
Repetier
March 2017
Enable Fan when 3D Printer is not idle (?)
137
views
7
comments
0
points
Most recent by
Repetier
February 2017
Converting Tronxy p802ma to repeter. Z homing problems and xy origin
206
views
1
comment
0
points
Most recent by
MartinH
February 2017
Looking for a primer for all the EEPROM settings.
45
views
1
comment
0
points
Most recent by
Repetier
February 2017
Cannot adjust nozzle distance from bed during print.
91
views
4
comments
0
points
Most recent by
Repetier
February 2017
Configuration tool
144
views
3
comments
0
points
Most recent by
ciro
February 2017
Using firmware wizard
66
views
1
comment
0
points
Most recent by
Repetier
February 2017
Problem with Simplify3D comments
74
views
8
comments
0
points
Most recent by
Tanuki44
February 2017
can't connect at the Baud rate i have set in config
32
views
2
comments
0
points
Most recent by
gorf25
February 2017
Four-armed (quattro) parallel delta printer
47
views
1
comment
0
points
Most recent by
Repetier
February 2017
ENDSTOP_Z_BACK_ON_HOME
116
views
10
comments
0
points
Most recent by
Repetier
February 2017
How to caculate the a b c towers for delta printer
108
views
10
comments
0
points
Most recent by
gorf25
February 2017
Detla probing adice - inconsistent correction still on delta
67
views
5
comments
0
points
Most recent by
RhinoRap
February 2017
not all settings downloaded
54
views
4
comments
0
points
Most recent by
Repetier
February 2017
new firmware (dev) in laser mode, log shows unknown commands. no laser activity
40
views
1
comment
0
points
Most recent by
Repetier
February 2017
AFTER FIRST LAYER PRINTS IN AIR
55
views
5
comments
0
points
Most recent by
Repetier
January 2017
delta printer levelling..... big problems
127
views
4
comments
0
points
Most recent by
RhinoRap
January 2017
Z AXIS TRAVEL DISTANCE IS DIFFERENT BETWEEN SOFTWARE AND ACTUAL WORLD
46
views
6
comments
0
points
Most recent by
MartinH
January 2017
Problem with Resend:0 through Pronterface
109
views
9
comments
0
points
Most recent by
Repetier
January 2017
new control board
36
views
0
comments
0
points
Started by
dmannion
January 2017
Filament Width Sensor
187
views
1
comment
0
points
Most recent by
Repetier
January 2017
Repetier Working on my robot arm 3d printer
288
views
34
comments
0
points
Most recent by
wangsamax
January 2017
«
1
…
5
6
7
8
9
10
11
…
17
»