General

• AUTOLEVEL - Homing with Z-PROBE and Servo

  482 views 4 comments 0 points Most recent by Jansinger July 2016
• DRIVE_SYSTEM

  310 views 16 comments 0 points Most recent by Eddiie July 2016
• Upgrading from Marlin for improved auto-leveling, suggestions?

  117 views 2 comments 0 points Most recent by CptanPanic July 2016
• Laser PWM or Heater Control

  324 views 1 comment 0 points Most recent by Repetier June 2016
• G92 Set position not shown on printer display

  201 views 3 comments 0 points Most recent by Repetier June 2016
• Heated bed but no extruder

  84 views 5 comments 0 points Most recent by Repetier June 2016
• File order on SD card

  113 views 1 comment 0 points Most recent by Repetier June 2016
• Repetier 0.92.9 printing mid air

  163 views 1 comment 0 points Most recent by Braccoz May 2016
• Disabling heated bed HELP

  143 views 1 comment 0 points Most recent by Repetier May 2016
• Compilation problems with Thermocouples- MAX31855

  694 views 4 comments 0 points Most recent by iH8u May 2016
• DUE and I2C Display

  144 views 5 comments 0 points Most recent by RAyWB May 2016
• Question regarding X_MAX_LENGTH, Y_MAX_LENGTH, and Configurator 092

  524 views 2 comments 0 points Most recent by Eddiie May 2016
• Need help to setup mixing extruder first time with 0.92.9

  799 views 8 comments 0 points Most recent by Eddiie May 2016
• Repetier-Firmware configuration tool for version 0.92.9 version

  432 views 2 comments 0 points Most recent by Repetier May 2016
• STM32F103

  158 views 1 comment 0 points Most recent by Repetier May 2016
• are tb68650 stepper drivers supported?

  109 views 7 comments 0 points Most recent by boelle May 2016
• Octorprint Error "Missing linenumber" with Repetier Firmware

  1.2K views 5 comments 0 points Most recent by Repetier May 2016
• Cnc clarifications

  167 views 2 comments 0 points Most recent by salvatoredc33 May 2016
• Cnc clarifications

  81 views 0 comments 0 points Started by salvatoredc33 May 2016
• Upgrade to 0.92 and compilation error

  83 views 1 comment 0 points Most recent by Repetier April 2016
• Does anyone have ANY idea what this error is all about?

  86 views 3 comments 0 points Most recent by hugetoughguy April 2016
• Error compiling for board Sanguino W/ ATmega1284p 16mhz

  438 views 1 comment 0 points Most recent by hugetoughguy April 2016
• "doesn't define a 'build.board' preference" ERROR verifying firmware

  1.7K views 1 comment 0 points Most recent by hugetoughguy April 2016
• "exec: "-w": executable file not found in %PATH%" ERROR

  608 views 4 comments 0 points Most recent by hugetoughguy April 2016
• LOTS of error messages when trying to verify firmware

  258 views 11 comments 0 points Most recent by hugetoughguy April 2016
• Can´t upload firmware, wheres the error dont get it

  388 views 4 comments 0 points Most recent by Repetier April 2016
• How do you change the Effector Radius

  67 views 1 comment 0 points Most recent by Repetier April 2016
• Bed leveling not good

  254 views 1 comment 0 points Most recent by Repetier April 2016
• z-probing - understanding ask

  179 views 1 comment 0 points Most recent by Repetier March 2016
• Hot to set #define Z_PROBE_X1 ?

  323 views 6 comments 0 points Most recent by Repetier March 2016