General

• Upgrading firmware from .83 to .92

  86 views 1 comment 0 points Most recent by Repetier March 2016
• z-probe and leveling

  236 views 2 comments 0 points Most recent by kintakunte March 2016
• Autoleveling with Repetier constantly failing

  310 views 1 comment 0 points Most recent by googliola March 2016
• Communication with printer issue

  295 views 1 comment 0 points Most recent by skal March 2016
• Stop ok 0 output

  172 views 1 comment 0 points Most recent by Repetier March 2016
• New to Repetier need help with Z probe height

  310 views 7 comments 0 points Most recent by randyf1965 March 2016
• Violation of the guidelines of open source / GPL by chinese producers

  116 views 2 comments 0 points Most recent by osnwt March 2016
• Melzi + Z Probe (Another Auto Level Question)

  1.3K views 4 comments 0 points Most recent by osnwt March 2016
• New Delta - effector not tracking flat during print? - help with autolevel/correction

  197 views 0 comments 0 points Started by MrBaz March 2016
• Questions about setup repetier firmware

  124 views 0 comments 0 points Started by MrZortrax March 2016
• Manual SD Mount

  239 views 4 comments 0 points Most recent by Hecot March 2016
• M505 ROD_RADIUS is not set to default factory settings.

  229 views 2 comments 0 points Most recent by Repetier March 2016
• Micro- switch initiated pause control for end filament or filament break.

  814 views 9 comments 0 points Most recent by Repetier March 2016
• Z Probe homes after every measurement

  156 views 4 comments 0 points Most recent by Repetier February 2016
• G30 mistery

  285 views 8 comments 0 points Most recent by marcoleo February 2016
• Can't compile when using new "Probe only with hot extruder (Z_PROBE_REQUIRES_HEATING)"

  237 views 1 comment 0 points Most recent by Repetier February 2016
• Cannot compile Repetier with full graphics support

  186 views 1 comment 0 points Most recent by Repetier February 2016
• C ++ program

  51 views 1 comment 0 points Most recent by Repetier February 2016
• CNC Firmware

  740 views 2 comments 0 points Most recent by orbita February 2016
• How do I assign a digital pin to a port on ATMega 2560. It seems the pin assignment in pins.h is al

  295 views 2 comments 0 points Most recent by CharlesMakeAll February 2016
• Thermistor temp table

  374 views 3 comments 0 points Most recent by R_Klauco February 2016
• Setting Esteps for specific extruder

  91 views 2 comments 0 points Most recent by austin00 January 2016
• Two extruders w/PID control and two part fans - Possible on RAMPS 1.4?

  176 views 3 comments 0 points Most recent by Repetier January 2016
• Laser won't turn on on 0.92.8

  251 views 4 comments 0 points Most recent by Repetier January 2016
• Clarification needed on "High Pin Enables" when setting up Laser/CNC in Repetier firmware

  241 views 2 comments 0 points Most recent by CharlesMakeAll January 2016
• Z-probing and G29

  245 views 3 comments 0 points Most recent by Repetier January 2016
• Compilation error version 1.6.xxx

  1.8K views 9 comments 0 points Most recent by Repetier January 2016
• code won't compile

  176 views 1 comment 0 points Most recent by Repetier January 2016
• G0 Z0.254 command not executed?? Repetier host with repetier firmware starts print at 15mm

  205 views 5 comments 0 points Most recent by magillus December 2015
• Need some help in setting up Repetier host FW on my mini-Kossel

  166 views 1 comment 0 points Most recent by Repetier December 2015