General

• DEV2: Description of dead time heater

  1 view 20 comments 0 points Most recent by karl_ranseier November 2020
• Z-Probe triggers high question

  1 view 3 comments 0 points Most recent by Repetier November 2020
• Looking for configuration file for Boxzy

  1 view 4 comments 0 points Most recent by RAyWB November 2020
• DEV2: M9999 after fatal state not allowed

  1 view 1 comment 0 points Most recent by Repetier October 2020
• Dev2: G30 always homes first

  1 view 37 comments 0 points Most recent by karl_ranseier October 2020
• DEV2: DIR signal at low speed

  1 view 13 comments 0 points Most recent by karl_ranseier October 2020
• Dev2: Cleanup of configuration.h

  1 view 2 comments 0 points Most recent by karl_ranseier October 2020
• Homing confusing

  1 view 15 comments 0 points Most recent by Repetier October 2020
• Rumba32: Servo position at start and after "auto-off"

  1 view 2 comments 0 points Most recent by karl_ranseier October 2020
• mesh bed leveling

  1 view 3 comments 0 points Most recent by Repetier October 2020
• Software Reset during auto level

  1 view 9 comments 0 points Most recent by karl_ranseier September 2020
• hot end temp plateaus before reaching target temp

  1 view 9 comments 0 points Most recent by RAyWB August 2020
• How to Z Probe and get value at a single point

  1 view 2 comments 0 points Most recent by jvbiondo July 2020
• Manual Delta calibration. Escher calculator and distortion correction issue.

  1 view 3 comments 0 points Most recent by Repetier July 2020
• Bed leveling issues.

  1 view 18 comments 0 points Most recent by Repetier July 2020
• Using Max Z Endstop as a Backup

  1 view 1 comment 0 points Most recent by Repetier June 2020
• downgrade from 1.0.3

  1 view 8 comments 0 points Most recent by ariellarraburu June 2020
• Homing to X MAX behaves weird

  1 view 13 comments 0 points Most recent by benecito June 2020
• Is version 0.60 of the Repetier Firmware available?

  1 view 2 comments 0 points Most recent by RAyWB June 2020
• x-y offset of print due to z-probe offset

  1 view 5 comments 0 points Most recent by frans87 June 2020
• Trouble compiling Repetier Firmware with Auto Level Probe Enabled

  1 view 1 comment 0 points Most recent by Repetier June 2020
• Issue with printing ratio

  1 view 1 comment 0 points Most recent by Repetier May 2020
• Z-probing changes Z height

  1 view 9 comments 0 points Most recent by Repetier May 2020
• Problems with small arcs G2/G3

  1 view 11 comments 0 points Most recent by Tricubik April 2020
• Disable autolevel?

  1 view 2 comments 0 points Most recent by EGropp April 2020
• Z-Offset - Sensor - Repetier Host - Not LCD Screen

  1 view 1 comment 0 points Most recent by Repetier April 2020
• problems with axis movement on 3d printer

  1 view 1 comment 0 points Most recent by Repetier March 2020
• Printer won't function till connected to host.

  1 view 4 comments 0 points Most recent by Nate3Der523 March 2020
• DaVinci Pro 1

  1 view 1 comment 0 points Most recent by Repetier March 2020
• Linear Advances makes curved surfaces very rough

  1 view 4 comments 0 points Most recent by PoWl January 2020