Recent Discussions

• verbindung statt usb auch über tx und rx möglich ?

  1 view 3 comments 0 points Most recent by Repetier March 2021Repetier-Server
• Jam filament Sensor

  1 view 5 comments 0 points Most recent by Repetier March 2021Repetier-Host
• BED Visualisierung

  1 view 13 comments 0 points Most recent by Repetier March 2021Repetier-Server
• USB Verbindung wird nach Neustart Drucker nicht wieder hergestellt, SKR 1.3 Marlin 2.0

  1 view 9 comments 0 points Most recent by Tschosef March 2021Repetier-Server
• Driver not downloading

  1 view 4 comments 0 points Most recent by Repetier March 2021Windows
• How to configure my printer with Ultratronics board and repetier firmware from scratch

  1 view 0 comments 0 points Started by atsiri March 2021 Repetier-Firmware
• non riesco ha connettere la mia stampante 3d al pc

  1 view 0 comments 0 points Started by joseph March 2021 Tips & Tricks
• gpio pin out

  1 view 3 comments 0 points Most recent by Repetier March 2021Questions & Answers
• Error: M221: No tool selected

  1 view 4 comments 0 points Most recent by Repetier March 2021Repetier-Server
• Repetier Server 0.90.7 und Anycubic Chiron Firmware 1.2.8

  1 view 14 comments 0 points Most recent by Repetier March 2021Repetier-Server
• Marlin 2.0.x Line numbers

  1 view 10 comments 0 points Most recent by mcpovel March 2021Bug Reports
• 1.0.4. Mac temperature stops updating

  1 view 1 comment 0 points Most recent by wildfang March 2021Bug Reports
• Webcam appears to not work with .local URL

  1 view 4 comments 0 points Most recent by AngryDad March 2021Bug Reports
• Run 2 separate mixing Hotends

  1 view 4 comments 0 points Most recent by rhklein March 2021Questions & Answers
• Repetier Server (only!) severe underextrusion since BMG upgrade

  1 view 17 comments 0 points Most recent by wildfang March 2021Repetier-Server
• Marlin progress out of sync

  1 view 5 comments 0 points Most recent by Repetier March 2021Bug Reports
• Prusa Mini Druckfarm / Drucker bleiben einfach mitten im Druck stehen

  1 view 7 comments 0 points Most recent by Repetier March 2021Repetier-Server
• Hilfe Heizbett heizt auf 90 Grad

  1 view 6 comments 0 points Most recent by Repetier March 2021Bug Reports
• Problem with probe setting in firmware repeater.

  1 view 2 comments 0 points Most recent by bartez81 March 2021Repetier-Firmware
• DEV2: Homing if endstop is much more far away than expected

  1 view 2 comments 0 points Most recent by karl_ranseier March 2021Bug Reports
• wifi

  1 view 2 comments 0 points Most recent by Repetier March 2021Questions & Answers
• Qnap nas installation

  1 view 1 comment 0 points Most recent by Repetier March 2021Linux
• Dev.2 Layer shift, Filament Sensor, Z-Bewegungen.

  1 view 14 comments 0 points Most recent by karl_ranseier March 2021Bug Reports
• I want to start from zero !!!

  1 view 5 comments 0 points Most recent by Angelo March 2021Linux
• Raspberry Pi 4 WLAN Verbindung nicht möglich

  1 view 2 comments 0 points Most recent by algenbrot March 2021Repetier-Server
• DEV2: Clean installation not compiling

  1 view 5 comments 0 points Most recent by karl_ranseier March 2021General
• Loss of extruder sensors when I put the SD card on a DaVinci DUO

  1 view 0 comments 0 points Started by Steph35 March 2021 Bug Reports
• PiZero W - Keine Wlan Verbindung

  1 view 4 comments 0 points Most recent by jmhoff March 2021Repetier-Server
• Vorschaubilder / ArcWelder

  1 view 1 comment 0 points Most recent by Repetier March 2021Repetier-Server
• Changing Park Command move order

  1 view 2 comments 0 points Most recent by EngineeringGuy March 2021Repetier-Host