Recent Discussions

• Anycubic Vyper filament sensor

  1 view 5 comments 0 points Most recent by Repetier January 6General
• Melzi 2.0 BLTouch Servo Pin A4 how to define the PIN ?

  617 views 3 comments 0 points Most recent by vinibali January 5Motherboard
• Boards mit einer Kommunikationsschnittstelle über TCP/IP Verbindung

  1 view 0 comments 0 points Started by tenda3 January 4 Repetier-Server
• Reading Chamber Temperature

  1 view 6 comments 0 points Most recent by repman January 3General
• Repetier- Server 1.4.15 (Linux) - Anycubic Kobra Max - Filamentwechsel

  1 view 1 comment 0 points Most recent by Repetier January 3Questions & Answers
• Anycubic Kobra Max - Druckauftrag im Display

  1 view 2 comments 0 points Most recent by BenLue January 3Questions & Answers
• Anycubic i3 Mega

  1 view 1 comment 0 points Most recent by Repetier January 2Linux
• PI4 & Arducam Rev.C (OV5647) ohne Drucker anzeigen/testen?

  1 view 3 comments 0 points Most recent by CBX_Micha January 2Repetier-Server
• Input Shaper Fehler mit Update auf 1.4.15

  1 view 3 comments 0 points Most recent by Toyoco January 2Repetier-Server
• MQTT GPIO

  1 view 14 comments 0 points Most recent by CappuccinoCake January 1Tips & Tricks
• Repetier Server and Klipper

  1 view 1 comment 0 points Most recent by Repetier December 2023Questions & Answers
• Mac M1 Unknown Printer Firmware

  1 view 1 comment 0 points Most recent by Repetier December 2023Repetier-Firmware
• Slicer incompatible to my 3D printer

  1 view 0 comments 0 points Started by yiqunli December 2023 Repetier-Host
• 32 bit

  1 view 2 comments 0 points Most recent by trumancabral December 2023Repetier-Firmware
• Auf den Repetier server von überall zugreifen

  1 view 1 comment 0 points Most recent by Repetier December 2023General
• Repetier Server startet nicht mehr

  1 view 9 comments 0 points Most recent by Repetier December 2023Linux
• Raspberry Pi Zero webcam not working

  1 view 1 comment 0 points Most recent by Repetier December 2023Questions & Answers
• BGCODE support

  1 view 2 comments 0 points Most recent by zekcode December 2023Feature Requests
• GPIO Pins / start of print job

  1 view 8 comments 0 points Most recent by Baelt December 2023Questions & Answers
• Wait for external signal before executing G-Code command

  1 view 6 comments 0 points Most recent by 3D_Le December 2023Repetier-Firmware
• possibility of choosing the number of prints

  1 view 4 comments 0 points Most recent by Baelt December 2023Questions & Answers
• Duplicate on the bed...

  1 view 1 comment 0 points Most recent by Repetier December 2023Feature Requests
• Multiple Cameras

  1 view 1 comment 0 points Most recent by Repetier December 2023Feature Requests
• gcode Befehle bearbeiten geht nach Repetier Server update auf 1.4.15 nicht mehr

  1 view 2 comments 0 points Most recent by flyer2000 December 2023Bug Reports
• IPv6 Konfiguration Raspberry Pi

  1 view 0 comments 0 points Started by Yachti December 2023 Tips & Tricks
• Kobra Max - immer wieder nervige Abbrüche...

  1 view 11 comments 0 points Most recent by Inf1n1ty33 December 2023Repetier-Server
• Temperature Chart shows PWM instead of percent

  1 view 8 comments 0 points Most recent by danym21 December 2023Bug Reports
• Upgrade to Firmware V2 on Ultratronics Board

  1 view 5 comments 0 points Most recent by Repetier December 2023Motherboard
• elevar eixo z 5mm

  1 view 1 comment 0 points Most recent by Repetier December 2023General
• FLSUN SR filament sensor - usable with Repetier Server?

  1 view 11 comments 0 points Most recent by Jaroslav December 2023Questions & Answers