Recent Discussions

• what to buy

  1 view 1 comment 0 points Most recent by Repetier May 7Questions & Answers
• Upload Gcode to SD on main use RRF?

  1 view 1 comment 0 points Most recent by Repetier May 6Questions & Answers
• Independent dual extruder X offset

  1 view 1 comment 0 points Most recent by Repetier May 6Repetier-Server
• Filament Sensor bei Creality ender 5 plus

  1 view 5 comments 0 points Most recent by Mordo01 May 5Repetier-Server
• Cannot save slic3r configurations using Linux Appimage

  1 view 1 comment 0 points Most recent by Repetier May 3Slic3r
• Repetier freezes.

  1 view 3 comments 0 points Most recent by Repetier May 3Linux
• size is incorrect on the x-axis

  1 view 4 comments 0 points Most recent by Repetier May 2Repetier-Firmware
• Duet Filamentsensor abfrage

  1 view 8 comments 0 points Most recent by What May 2Repetier-Server
• Cura print configuration are all the same

  1 view 2 comments 0 points Most recent by jomo April 29CuraEngine
• The button connect to printer does not work

  1 view 7 comments 0 points Most recent by Winapster April 28Repetier-Host
• Repetier won't start beyond the splash screen...nothing happens

  1 view 16 comments 0 points Most recent by thewebsis April 28Repetier-Host
• Generated G-code not found

  1 view 5 comments 0 points Most recent by Repetier April 27Repetier-Host
• Fluid GUI

  1 view 4 comments 0 points Most recent by Repetier April 27Feature Requests
• Shutdown and GET-Request after all jobs are done

  1 view 8 comments 0 points Most recent by Repetier April 26Questions & Answers
• Can't get Repetier +Cura to generate supports properly

  1 view 1 comment 0 points Most recent by Repetier April 26CuraEngine
• Will Repetier-Host 2.3.1 run on Linux Mint 21.1

  1 view 5 comments 0 points Most recent by wa3scm April 25Repetier-Host
• Klipper Filament Sensor

  1 view 1 comment 0 points Most recent by Repetier April 25Repetier-Server
• Could this calibration tool be used with Repetier firware?

  1 view 1 comment 0 points Most recent by Repetier April 25Questions & Answers
• issues with printer

  1 view 1 comment 0 points Most recent by Repetier April 24Windows
• Druck bricht an beliebigen stellen ab. E/A Vorgang

  1 view 1 comment 0 points Most recent by Repetier April 23Questions & Answers
• Bulk Change Temps/Material in a Project

  1 view 2 comments 0 points Most recent by SonjaDCUSA April 23Feature Requests
• SKR Pico - Keine Verbindung - Kein Microcontroller

  1 view 2 comments 0 points Most recent by Repetier April 22Repetier-Server
• Klipper Befehle

  1 view 2 comments 0 points Most recent by marcus_w April 20Tips & Tricks
• Error: Expected line x got y seit Uprade von 1.3.x auf 1.4.x

  1 view 14 comments 0 points Most recent by Repetier April 20Bug Reports
• Babystep from WebInterface or Server Monitori

  1 view 4 comments 0 points Most recent by Marian April 20Repetier-Server
• Can't change z min pos

  1 view 10 comments 0 points Most recent by Repetier April 19Repetier-Host
• CRASH? Server won't let me connect, gives C++ code as response.

  1 view 2 comments 0 points Most recent by Repetier April 19Bug Reports
• Lin Advance setup

  1 view 10 comments 0 points Most recent by good_idea April 18Questions & Answers
• changing speeds between lines and curves

  1 view 4 comments 0 points Most recent by Repetier April 18Questions & Answers
• Recovery Settings to help recover from Windows Reboots

  1 view 1 comment 0 points Most recent by Repetier April 18Repetier-Server