Questions & Answers

• Question about Z probe offset

  34 views 1 comment 0 points Most recent by Repetier October 2017
• RADDS, Repetier and PWM

  62 views 11 comments 0 points Most recent by tpila1 September 2017
• Odd vertical lines showing up

  1K views 34 comments 0 points Most recent by Repetier September 2017
• How does the Light On/Off control work?

  643 views 12 comments 0 points Most recent by geoffreyforest September 2017
• Gcode parser error?

  21 views 2 comments 0 points Most recent by Alan September 2017
• need idea for end script

  63 views 10 comments 0 points Most recent by boelle September 2017
• Triggerable abort on pinchange/endstop

  18 views 1 comment 0 points Most recent by Repetier September 2017
• List of Repetier supported G & M Codes

  57 views 1 comment 0 points Most recent by Repetier September 2017
• Need help with RADDS on my Kossel XL Delta

  134 views 11 comments 0 points Most recent by SimonB September 2017
• CoreXY with FAST_COREXYZ defined is failing to home Z

  149 views 20 comments 0 points Most recent by DeJe September 2017
• Invert Fan Signal for Low Level Triggering MOSFETS

  37 views 2 comments 0 points Most recent by PM8471 September 2017
• Changes in 1.0.0dev since March

  36 views 1 comment 0 points Most recent by Repetier August 2017
• after starting server 0.86 and loging out now wont connect to Host

  34 views 7 comments 0 points Most recent by recoush August 2017
• Two Kossel Arduino Serial Connects Stopped Working?? Help?

  28 views 3 comments 0 points Most recent by Repetier August 2017
• Stepper issues with RADDS + DUE + RAPS128 (Cartesian printer)

  607 views 12 comments 0 points Most recent by Repetier August 2017
• RAMPS, Chimera and RRD Fan Extender

  29 views 0 comments 0 points Started by bipsen August 2017
• how to store Z for extruder0 and Z for extruder1

  56 views 1 comment 0 points Most recent by Repetier August 2017
• How to use serial communication on RADDS with serial Display from Sparklab ?

  88 views 6 comments 0 points Most recent by rgd July 2017
• Delta Homing Issue

  56 views 4 comments 0 points Most recent by n3delva July 2017
• Changelog for dev version

  38 views 4 comments 0 points Most recent by Mugga July 2017
• PAUSE via SD Card job doesn't Resume properly

  45 views 4 comments 0 points Most recent by thiagopeixoto16 July 2017
• Best replacment for Melzi board

  48 views 1 comment 0 points Most recent by Repetier June 2017
• Kossel Linear Plus Dimension error

  106 views 3 comments 0 points Most recent by Repetier June 2017
• Printer half-working after changing firmware, help?

  47 views 2 comments 0 points Most recent by Notsure June 2017
• Trying to install firmware. Novice needs help.

  45 views 1 comment 0 points Most recent by Repetier June 2017
• Two endstop, one signal

  45 views 1 comment 0 points Most recent by Repetier June 2017
• How to run SELECT_COMMANDS for extruder ?

  62 views 5 comments 0 points Most recent by Repetier June 2017
• Printer Does Not Start Printing when Using Simplify3D

  55 views 2 comments 0 points Most recent by kevintong116 May 2017
• G33 not implemented?

  48 views 3 comments 0 points Most recent by MartinH May 2017
• Driving Galvos with CustomEvent Script

  42 views 1 comment 0 points Most recent by Repetier May 2017