Questions & Answers

• Firmware Modification for PCB-Drilling

  1 view 0 comments 0 points Started by Tomm300 July 2018
• PS_ON not working as expected

  1 view 3 comments 0 points Most recent by DerIngenieur June 2018
• Laser mode E increasing

  1 view 4 comments 0 points Most recent by larssenden June 2018
• G32 S2 homes very slowly

  1 view 2 comments 0 points Most recent by Repetier June 2018
• Firmware modification for Plasma Touch Height Control(THC)

  1 view 1 comment 0 points Most recent by Repetier May 2018
• Can't upload Firmware

  1 view 10 comments 0 points Most recent by SoDamnInsane May 2018
• Change firmware on PowerSpec Pro 2

  1 view 0 comments 0 points Started by JimmyT May 2018
• Handling von Endstops

  1 view 4 comments 0 points Most recent by Buttons May 2018
• how to calculate Probe height Z_PROBE_HEIGHT??

  1 view 1 comment 0 points Most recent by Repetier May 2018
• Z Probe Home XY Strange behaviour

  1 view 5 comments 0 points Most recent by Repetier May 2018
• Retraction on tool change

  1 view 2 comments 0 points Most recent by bvkrieken May 2018
• Lin. Advance, Jerk and filament change

  1 view 7 comments 0 points Most recent by Repetier May 2018
• Can anyone share a configuration of a standard tech2c hypercube with RAMPS V1.4 ?

  1 view 1 comment 0 points Most recent by Repetier May 2018
• Z Probe moving in wrong Direction

  1 view 2 comments 0 points Most recent by wiremonkey May 2018
• Second Extruder not Heating on MKS Base V1.5

  1 view 1 comment 0 points Most recent by Repetier May 2018
• Jam Sensor

  1 view 1 comment 0 points Most recent by Repetier May 2018
• SHARED_EXTRUDER_HEATER = 1 not affecting temperature reading?

  1 view 4 comments 0 points Most recent by aschneid May 2018
• Re-purposing a 3D printer board to control a solenoid valve with Mcode

  1 view 2 comments 0 points Most recent by SmartCNC3D April 2018
• Z-Probing error reading diagonally with the grid

  1 view 16 comments 0 points Most recent by RAyWB April 2018
• Babystepping without an Display

  1 view 3 comments 0 points Most recent by Repetier April 2018
• Setting up a new thermistor

  1 view 2 comments 0 points Most recent by jmpinc April 2018
• Setup auto bed levelling 3D Touch and Rumba Board.

  430 views 2 comments 0 points Most recent by theohenrichs April 2018
• disable backlash compensation via gcode?

  1 view 6 comments 0 points Most recent by Repetier April 2018
• Move two independent extruders at the same time

  1 view 0 comments 0 points Started by aurror April 2018
• Help. Calibrate X and Y axis

  1 view 7 comments 0 points Most recent by Repetier April 2018
• Delta Distortion Correction Head is moving too high

  1 view 2 comments 0 points Most recent by Repetier March 2018
• Manual homing, no endstops

  1 view 2 comments 0 points Most recent by bbogdanmircea March 2018
• Extruder 2 stop heating 20C to early

  1 view 2 comments 0 points Most recent by PMGZED March 2018
• Distortion Correction Radius

  1 view 1 comment 0 points Most recent by Repetier March 2018
• cartesian and disortion correction

  1 view 25 comments 0 points Most recent by Roko March 2018