Questions & Answers

• Repetier Firmware on MKS GEN L

  1 view 42 comments 0 points Most recent by Repetier November 2020
• Motorized Bed Level Correction with 4 Independent Z Screws?

  1 view 38 comments 0 points Most recent by Repetier October 2020
• Total newbie trying to access firmware

  1 view 3 comments 0 points Most recent by Repetier October 2020
• Delta Tower Angle Adjustment

  1 view 3 comments 0 points Most recent by Cheddy October 2020
• The Z axis go down after "Z home" in CNC mode.

  1 view 11 comments 0 points Most recent by Repetier October 2020
• Limit switches occasionally ignored when homing

  1 view 1 comment 0 points Most recent by Repetier October 2020
• X/Y probe offset not used when bed leveling

  1 view 37 comments 0 points Most recent by opy01 October 2020
• Spindle control PWM output pin. etc.

  1 view 4 comments 0 points Most recent by plasmacut October 2020
• How to solve SD card reading problem

  1 view 6 comments 0 points Most recent by plasmacut September 2020
• Laser pwm frequenty low

  1 view 1 comment 0 points Most recent by Repetier September 2020
• V2 - Compilation Error with HEAT_MANAGER_BANG_BANG

  1 view 2 comments 0 points Most recent by frguy September 2020
• x and y ass setiings

  1 view 1 comment 0 points Most recent by Repetier September 2020
• Advanced manufacturing question, variables imbedded in code.

  1 view 1 comment 0 points Most recent by Repetier September 2020
• M221 and Advanced Ditto Printing

  1 view 12 comments 0 points Most recent by Repetier August 2020
• Total Noob with a DaVinci 2.0 (I think) printer - what are my options?

  1 view 1 comment 0 points Most recent by Repetier August 2020
• Zusatzschrittmotor für Filamentzufuhr

  1 view 3 comments 0 points Most recent by Repetier August 2020
• Re-assigning auto levelling points..

  1 view 1 comment 0 points Most recent by Repetier August 2020
• V2 Compilation Error

  1 view 1 comment 0 points Most recent by Repetier July 2020
• RADDS + DUE + RAPS128 + RADDS LCD 4x 20 Control panel

  1 view 23 comments 0 points Most recent by Repetier July 2020
• Z probe too high one side

  1 view 22 comments 0 points Most recent by Repetier June 2020
• Probleme mit "Z-correction"

  1 view 3 comments 0 points Most recent by Repetier June 2020
• Help with BL Touch Clone

  1 view 3 comments 0 points Most recent by Rimba May 2020
• Diamond Hotend

  1 view 1 comment 0 points Most recent by Repetier May 2020
• Go to new block position instead of previous position after tool change

  1 view 5 comments 0 points Most recent by Repetier May 2020
• BLTouch

  3.6K views 39 comments 0 points Most recent by fatice May 2020
• G2 arc command doesnot seem to follow feedrate commands

  1 view 5 comments 0 points Most recent by Repetier May 2020
• Can I boot with tool T2 instead of T0 in Firmware 1.0.4

  1 view 4 comments 0 points Most recent by Mikael May 2020
• Multiply Max temperatur on hotend in firmware

  1 view 1 comment 0 points Most recent by Repetier May 2020
• Delta printer does not see endstops

  1 view 8 comments 0 points Most recent by Repetier April 2020
• crash detection, power panic, and runout filament sensor Prusa mk3s

  1 view 1 comment 0 points Most recent by Repetier April 2020