Recent Discussions

• Spindle control PWM output pin. etc.

  1 view 4 comments 0 points Most recent by plasmacut October 2020Questions & Answers
• Keine WLAN-Verbindung mit Router möglich

  1 view 5 comments 0 points Most recent by Repetier October 2020Repetier-Server
• repetier-network.xml on sd card for pi 3

  1 view 4 comments 0 points Most recent by Repetier October 2020Repetier-Server
• WLAN configuration on sd card

  1 view 0 comments 0 points Started by raspgraph October 2020 Questions & Answers
• Passwort Eingabe nicht möglich

  1 view 1 comment 0 points Most recent by Repetier October 2020Questions & Answers
• Problems calling WebActions from Rest-API

  1 view 5 comments 0 points Most recent by Repetier October 2020General
• About G32 initial move necessity

  1 view 2 comments 0 points Most recent by lmcbmai October 2020Repetier-Firmware
• auto bed leveling not working

  1 view 0 comments 0 points Started by N1YDP October 2020 Motor Control
• connect to a printer with wireless tcp/ip in repetier server.

  1 view 4 comments 0 points Most recent by Ehrepet October 2020Repetier-Server
• Pusa Mini Drucker bleibt mitten im Druck stehen.

  1 view 2 comments 0 points Most recent by KAG October 2020Bug Reports
• Can we have a way to set speed up / down % based on layer ranges ?

  1 view 1 comment 0 points Most recent by Repetier October 2020Feature Requests
• Raspberry PI`s for camera picture

  1 view 3 comments 0 points Most recent by Repetier October 2020Repetier-Server
• Flash Prusa MK3S firmware using Repetier-server

  1 view 2 comments 0 points Most recent by NickRno77 September 2020Repetier-Server
• Additional endstops to the Z axis

  1 view 1 comment 0 points Most recent by Repetier September 2020Feature Requests
• G02 and G03 code issue

  1 view 6 comments 0 points Most recent by bpetrus September 2020Repetier-Firmware
• LED Licht einschalten bei Druckbeginn und abschalten bei Druckende

  1 view 16 comments 0 points Most recent by Repetier September 2020Questions & Answers
• Repetier host dont send M600 when sensor is Open

  1 view 5 comments 0 points Most recent by Repetier September 2020Repetier-Host
• FFMPEG Konvertierung total verpixelt

  1 view 1 comment 0 points Most recent by Repetier September 2020Questions & Answers
• Discussion about this forum

  1 view 1 comment 0 points Most recent by Repetier September 2020General
• Move the non current Extruder on Toolchange

  1 view 1 comment 0 points Most recent by Repetier September 2020Repetier-Firmware
• Drucker bleibt einfach stehen

  1 view 2 comments 0 points Most recent by Repetier September 2020Bug Reports
• Homing not working as expected (does not stop)

  1 view 5 comments 0 points Most recent by karl_ranseier September 2020Motor Control
• Experience RUMBA32 installation (and upload problem)

  1 view 29 comments 0 points Most recent by karl_ranseier September 2020Repetier-Firmware
• G-Code does not reflect selected Print and Filament Cura-Engine-Settings when saved

  1 view 0 comments 0 points Started by Erro11 September 2020 Repetier-Host
• DEV: Stabilize temperature corridor

  79 views 12 comments 0 points Most recent by m0dd0 September 2020Bug Reports
• Login wird verlangt

  1 view 2 comments 0 points Most recent by Repetier September 2020General
• Connection in Web Interface

  1 view 3 comments 0 points Most recent by Gerald September 2020General
• not able to print

  1 view 1 comment 0 points Most recent by Repetier September 2020Repetier-Server
• XYZ Control Speed and WEBCAM

  1 view 6 comments 0 points Most recent by NickRno77 September 2020Questions & Answers
• Rendering the Gcode image too small

  1 view 5 comments 0 points Most recent by NickRno77 September 2020Repetier-Server