Recent Discussions

• Klipper Forked Version

  1 view 4 comments 0 points Most recent by Repetier November 2022Repetier-Server
• Extruder Stepper doesn't hold position

  1 view 2 comments 0 points Most recent by Repetier November 2022Repetier-Firmware
• Cannot load Repetier Server in iframe?

  1 view 3 comments 0 points Most recent by Repetier November 2022General
• Manual Bed Leveling Wizard

  1 view 3 comments 0 points Most recent by Repetier November 2022Bug Reports
• Printer suddenly stops mid print

  1 view 10 comments 0 points Most recent by Repetier November 2022Windows
• es Funktioniert einfach nicht mit Cura 5.2.1

  1 view 2 comments 0 points Most recent by marcus_w November 2022CuraEngine
• Repetier Server Kliper Canbus

  1 view 19 comments 0 points Most recent by Repetier November 2022Repetier-Server
• Trying to control two pins seperatly with M106/M107 commands

  1 view 4 comments 0 points Most recent by sgregory November 2022Questions & Answers
• "MAXTEMP triggered" but Extruder at 0 degrees.

  1 view 5 comments 0 points Most recent by Repetier November 2022Extruder & Bed
• Slic3r Plugin Problems.

  1 view 2 comments 0 points Most recent by Repetier November 2022Repetier-Host
• Firmware 1.0.4dev for Blue Eagle Labs Kossel Clear delta

  1 view 7 comments 0 points Most recent by billmania November 2022Repetier-Firmware
• TCP/IP Connected Printer Shows as Connected when Powered Off

  1 view 4 comments 0 points Most recent by geofabrica November 2022Repetier-Server
• System Hangup

  1 view 9 comments 0 points Most recent by Repetier November 2022Bug Reports
• Repetier Server Dienst lässt sich nicht mehr starten...!

  1 view 1 comment 0 points Most recent by Repetier November 2022Questions & Answers
• Any info on the next major update to Server?

  1 view 1 comment 0 points Most recent by Repetier November 2022Repetier-Server
• Gehäuselüfter mit DS18B20 und PWM an Raspberry

  1 view 1 comment 0 points Most recent by Repetier November 2022Repetier-Server
• MPCNC randomly wrong milling paths

  1 view 1 comment 0 points Most recent by Repetier November 2022Repetier-Host
• Repetier informer - Can't create groupe (Unknown device)

  1 view 0 comments 0 points Started by zekcode November 2022 Bug Reports
• Rotate Raspberry Pi screen image

  57 views 17 comments 0 points Most recent by Repetier October 2022Repetier-Server
• Webcam Stream steht auf dem Kopf

  1 view 1 comment 0 points Most recent by Repetier October 2022Tips & Tricks
• Edit gcode in projects

  1 view 4 comments 0 points Most recent by Repetier October 2022Feature Requests
• Touchscreen not working after new install on Rpi

  1 view 6 comments 0 points Most recent by umtauscher October 2022Questions & Answers
• Cant add to printer queue after a print has been started

  1 view 11 comments 0 points Most recent by Ondy October 2022General
• Can only run Repetier-Host under sudo?

  1 view 5 comments 0 points Most recent by [Deleted User] October 2022Repetier-Host
• Extruding problems

  1 view 3 comments 0 points Most recent by Rotten00 October 2022Questions & Answers
• Durch Installation am haben sich beim Extruder Steps/mm verändert

  1 view 2 comments 0 points Most recent by Rotten00 October 2022Motor Control
• Repetier erkennt die Firmware nicht

  1 view 6 comments 0 points Most recent by Repetier October 2022Display & Keyboard
• Key verlegt

  1 view 2 comments 0 points Most recent by sayohh October 2022Repetier-Server
• Lost licence key

  1 view 4 comments 0 points Most recent by sayohh October 2022Repetier-Firmware
• Quick Commands - Logging Output

  1 view 3 comments 0 points Most recent by Repetier October 2022Questions & Answers