Recent Discussions

Linzers vergessen von Pi zu deaktivieren

1 view 1 comment 0 points Most recent by Repetier December 2022Questions & Answers

Zeitberechnunf Cura vs. Repetier

1 view 1 comment 0 points Most recent by Repetier December 2022Questions & Answers

Motion problems with the Z axis

1 view 1 comment 0 points Most recent by Repetier November 2022Repetier-Firmware

Druck bricht kurz nach dem Start ab: Receiving only error messages. Reset communications for printer

1 view 6 comments 0 points Most recent by DaniSoB November 2022Repetier-Server

Repetier-Server auf Raspberry Pi langsam

1 view 11 comments 0 points Most recent by LionMars November 2022Repetier-Server

Slicer tab - Bug when scrolling over WatchDirectory list

1 view 3 comments 0 points Most recent by Repetier November 2022Bug Reports

WLAN connection problem

1 view 6 comments 0 points Most recent by Repetier November 2022Repetier-Server

Elyarchi Amabox Troubleshoot

1 view 0 comments 0 points Started by amayaatp November 2022 Questions & Answers

Static IP

1 view 1 comment 0 points Most recent by Repetier November 2022Questions & Answers

Error whilst autotuning PID for high temperature printing

1 view 2 comments 0 points Most recent by Repetier November 2022Extruder & Bed

extruder wizard is not working anycubic vyper

1 view 3 comments 0 points Most recent by Repetier November 2022Repetier-Server

Klipper Ender 7

1 view 1 comment 0 points Most recent by Repetier November 2022Questions & Answers

Random reboots after updating to 1.4.3

1 view 3 comments 0 points Most recent by Repetier November 2022Repetier-Server

Printers stopped for few sec, console message included

1 view 20 comments 0 points Most recent by pantherius November 2022Bug Reports

ramps 1.4 issue with 3 extruder motors

1 view 4 comments 0 points Most recent by recoush November 2022General

Z-axis manual command inverted in Windows 10

1 view 3 comments 0 points Most recent by Repetier November 2022Windows

What's the most key point when you decide to get a 3d printer

1 view 2 comments 0 points Most recent by recoush November 2022General

Bewegung Y passt nicht auf Druckbett

1 view 4 comments 0 points Most recent by firewire November 2022Extruder & Bed

printing with server proG-code error with M539?

1 view 13 comments 0 points Most recent by Repetier November 2022General

MQTT or HTTP Message when Shutdown server

1 view 7 comments 0 points Most recent by Ikswoknib November 2022General

Object Placement / Auto Position - to recognize Prusaslicer Complete Individual Objects

1 view 1 comment 0 points Most recent by Repetier November 2022Feature Requests

Webhook zum ausschalten für zwei Drucker nutzen (wenn beide fertig sind)

1 view 3 comments 0 points Most recent by Repetier November 2022Repetier-Server

Wlan Verbindungs Problem

1 view 1 comment 0 points Most recent by Repetier November 2022Repetier-Server

Job Upload

1 view 3 comments 0 points Most recent by Repetier November 2022Questions & Answers

Autolevel height problem

1 view 1 comment 0 points Most recent by Repetier November 2022Questions & Answers

Print Queue - Reihnfolge ändern

1 view 8 comments 0 points Most recent by Repetier November 2022Feature Requests

Is there an Abort Current Move command?

1 view 4 comments 0 points Most recent by jvbiondo November 2022Repetier-Firmware