Repetier-Host

Child Categories

• News

  5 discussions 13 comments

• General

  296 discussions 976 comments

• Windows

  241 discussions 1.1K comments

• Linux

  104 discussions 376 comments

• Mac

  77 discussions 266 comments

• CuraEngine

  89 discussions 293 comments

• Slic3r

  141 discussions 441 comments

• Bug Reports

  203 discussions 705 comments

• Questions & Answers

  415 discussions 1.6K comments

• Tips & Tricks

  28 discussions 116 comments

• Feature Requests

  119 discussions 293 comments

• Second extruder doesn't heat

  1 view 2 comments 0 points Most recent by Repetier May 31
• Rep-Host won't start after adding new Slicer

  1 view 7 comments 0 points Most recent by Braccoz May 30
• Repetier not sensing that printer is heated

  1 view 1 comment 0 points Most recent by Repetier May 26
• Launcher to use Slic3r Prusa Edition 2.0 from within Repetier-Host 2.1.3

  1 view 0 comments 0 points Started by MrMabulous May 22
• Unknown firmware protocol

  1 view 1 comment 0 points Most recent by Repetier May 6
• Is it possible to run a multi-material print with different print settings?

  1 view 1 comment 0 points Most recent by Repetier May 1
• Non manifold error extrange

  1 view 2 comments 0 points Most recent by guardianrexar April 24
• Keine Grafische Oberfläche auf Pi3

  1 view 2 comments 0 points Most recent by geri April 18
• Slic3r PE 1.41.3+ / RH 2.1.3 - weird artefact after sliced; wrong predicted filament length

  1 view 3 comments 0 points Most recent by Repetier April 15
• No EEPROM reading on Host V. 2.0

  367 views 13 comments 0 points Most recent by Repetier April 14
• Unwanted Travel

  1 view 1 comment 0 points Most recent by Repetier April 6
• Userinterface questions

  1 view 1 comment 0 points Most recent by Repetier March 31
• A question about speed and temperature.

  1 view 3 comments 0 points Most recent by Repetier March 29
• communication timeout - reset send buffer block

  1 view 5 comments 0 points Most recent by Repetier March 24
• auf welchem Linux System läuft es stabil

  1 view 1 comment 0 points Most recent by Repetier March 24
• Searching for Postprocessor for Fusion 360

  1 view 3 comments 0 points Most recent by Maashkinoozhe March 24
• no print option on SD card

  1 view 6 comments 0 points Most recent by Repetier March 23
• How can i pass the parameter?

  1 view 8 comments 0 points Most recent by Repetier March 15
• Print

  1 view 4 comments 0 points Most recent by Jules March 12
• 1.sensor defect error 2.printer runs into dry mode,

  1 view 2 comments 0 points Most recent by Repetier March 12
• 3D Printer Printing Gaps in Between Layers

  1 view 3 comments 0 points Most recent by Repetier March 8
• Model Missing Layers When Slicing

  1 view 7 comments 0 points Most recent by Repetier March 8
• Is it possible to output Slic3r/CuraEngine setting through Repetier-host API?

  1 view 1 comment 0 points Most recent by Repetier March 5
• Alfawise U30

  1 view 1 comment 0 points Most recent by Repetier March 4
• Printer does continue printing

  1 view 1 comment 0 points Most recent by Repetier March 4
• fatal:Heater/sensor error - M999

  1 view 5 comments 0 points Most recent by Repetier February 28
• Commands waiting?

  11.6K views 19 comments 0 points Most recent by dom58 February 27
• My extruder won't heat up

  889 views 10 comments 0 points Most recent by MartinH February 27
• I don't see file on SD Card in Alfawise U20

  1 view 1 comment 0 points Most recent by Repetier February 25
• connect to anet a8 (prusa i3?)

  1 view 17 comments 0 points Most recent by jardajsb February 14