Repetier-Host

Child Categories

• News

  8 discussions 16 comments

• General

  344 discussions 1.1K comments

• Windows

  281 discussions 1.3K comments

• Linux

  121 discussions 440 comments

• Mac

  84 discussions 285 comments

• CuraEngine

  115 discussions 374 comments

• Slic3r

  153 discussions 524 comments

• Bug Reports

  230 discussions 843 comments

• Questions & Answers

  463 discussions 1.8K comments

• Tips & Tricks

  33 discussions 125 comments

• Feature Requests

  134 discussions 330 comments

• Launcher to use Slic3r Prusa Edition 2.0 from within Repetier-Host 2.1.3

  1 view 0 comments 0 points Started by MrMabulous May 2019
• Unknown firmware protocol

  1 view 1 comment 0 points Most recent by Repetier May 2019
• Is it possible to run a multi-material print with different print settings?

  1 view 1 comment 0 points Most recent by Repetier May 2019
• Non manifold error extrange

  1 view 2 comments 0 points Most recent by guardianrexar April 2019
• Keine Grafische Oberfläche auf Pi3

  1 view 2 comments 0 points Most recent by geri April 2019
• Slic3r PE 1.41.3+ / RH 2.1.3 - weird artefact after sliced; wrong predicted filament length

  1 view 3 comments 0 points Most recent by Repetier April 2019
• No EEPROM reading on Host V. 2.0

  367 views 13 comments 0 points Most recent by Repetier April 2019
• Unwanted Travel

  1 view 1 comment 0 points Most recent by Repetier April 2019
• Userinterface questions

  1 view 1 comment 0 points Most recent by Repetier March 2019
• A question about speed and temperature.

  1 view 3 comments 0 points Most recent by Repetier March 2019
• communication timeout - reset send buffer block

  1 view 5 comments 0 points Most recent by Repetier March 2019
• auf welchem Linux System läuft es stabil

  1 view 1 comment 0 points Most recent by Repetier March 2019
• no print option on SD card

  1 view 6 comments 0 points Most recent by Repetier March 2019
• How can i pass the parameter?

  1 view 8 comments 0 points Most recent by Repetier March 2019
• Print

  1 view 4 comments 0 points Most recent by Jules March 2019
• 1.sensor defect error 2.printer runs into dry mode,

  1 view 2 comments 0 points Most recent by Repetier March 2019
• 3D Printer Printing Gaps in Between Layers

  1 view 3 comments 0 points Most recent by Repetier March 2019
• Model Missing Layers When Slicing

  1 view 7 comments 0 points Most recent by Repetier March 2019
• Is it possible to output Slic3r/CuraEngine setting through Repetier-host API?

  1 view 1 comment 0 points Most recent by Repetier March 2019
• Alfawise U30

  1 view 1 comment 0 points Most recent by Repetier March 2019
• Printer does continue printing

  1 view 1 comment 0 points Most recent by Repetier March 2019
• fatal:Heater/sensor error - M999

  1 view 5 comments 0 points Most recent by Repetier February 2019
• Commands waiting?

  11.6K views 19 comments 0 points Most recent by dom58 February 2019
• My extruder won't heat up

  889 views 10 comments 0 points Most recent by MartinH February 2019
• I don't see file on SD Card in Alfawise U20

  1 view 1 comment 0 points Most recent by Repetier February 2019
• CONNEXION WIFI

  1 view 1 comment 0 points Most recent by Repetier February 2019
• Start signal not detected

  1 view 8 comments 0 points Most recent by Twistedair February 2019
• Pan button?

  1 view 2 comments 0 points Most recent by psyon February 2019
• Repetier Server on Raspberry Pi 3's

  1 view 2 comments 0 points Most recent by psaccess January 2019
• Layer Height 0.05

  1 view 2 comments 0 points Most recent by shearder January 2019