Windows

• OpenGL 1.5 Install

  1 view 1 comment 0 points Most recent by Repetier May 2018
• Format Error , Wrong Checksum , Extrusion Stops

  2.5K views 10 comments 0 points Most recent by Repetier May 2018
• How to retrieve slicer (printing parameters) config from a hard-drive?

  1 view 2 comments 0 points Most recent by khondoke May 2018
• windows 8 connects but have no manual control and printer not reporting back to computer.

  1 view 1 comment 0 points Most recent by Repetier April 2018
• Repetier Host 2.0.5 crashes on startup

  1 view 3 comments 0 points Most recent by maich April 2018
• Repetier Host 2.0.5 hangs on startup WIN10

  1 view 1 comment 0 points Most recent by Repetier April 2018
• How to get the test piece to work properly

  1 view 1 comment 0 points Most recent by MartinH April 2018
• Bed won't heat

  1 view 2 comments 0 points Most recent by grayknight235 March 2018
• Can't go below Z0 even with end stops disabled - How to calibrate then?

  1 view 7 comments 0 points Most recent by Repetier March 2018
• Configure USB port

  1 view 1 comment 0 points Most recent by Repetier March 2018
• TCP/IP Settings

  722 views 2 comments 0 points Most recent by tomv March 2018
• Re-Arm Smoothieware TCP/IP

  1 view 2 comments 0 points Most recent by Repetier March 2018
• Heat extruder works only with command line

  1 view 1 comment 0 points Most recent by Repetier March 2018
• Separate printing

  1 view 1 comment 0 points Most recent by MartinH March 2018
• Unhandled exception has occured | Maximum baud rate

  1 view 4 comments 0 points Most recent by Shinnifura March 2018
• (Partial) connection issue and crash

  1 view 3 comments 0 points Most recent by Damian071 February 2018
• Step by step debuging

  1 view 2 comments 0 points Most recent by guffy January 2018
• Preview does not show the object to the top

  1 view 3 comments 0 points Most recent by jarmilitao January 2018
• printer display in Host

  1 view 1 comment 0 points Most recent by Repetier December 2017
• Upload to sd card via repetier host gets a 0 byte file size?

  76 views 9 comments 0 points Most recent by Myndale December 2017
• Old XP machine without root certificates

  1 view 1 comment 0 points Most recent by Repetier December 2017
• Problem with 3d printer receiving commands

  1 view 8 comments 0 points Most recent by Roko December 2017
• Question about Baud Rate and Arduino Due COM port driver

  1 view 1 comment 0 points Most recent by Repetier December 2017
• Updating CuraEngine

  1 view 2 comments 0 points Most recent by sonnaps December 2017
• Unable to install Repetier Host

  1 view 1 comment 0 points Most recent by Repetier November 2017
• G-Code

  1 view 3 comments 0 points Most recent by Repetier November 2017
• Install question - found 5 heat sinks with 3D printer but no instructions on what to do

  1 view 1 comment 0 points Most recent by Repetier November 2017
• Connect to repetier host: Yes, Recieve commands: No

  84 views 8 comments 0 points Most recent by willemx2 November 2017
• slicer to print errors

  31 views 2 comments 0 points Most recent by frankenstein November 2017
• No graphic after slicing and while printing

  37 views 4 comments 0 points Most recent by WalkerKD October 2017