Windows

• Rendering problems: missing chunks of filament in 3D preview

  1 view 3 comments 0 points Most recent by Repetier April 2019
• Can't connect to i3 MK2S: Endless loop of Error:Line Number is not Last Line Number+1, Last Line: 0

  1 view 8 comments 0 points Most recent by Repetier April 2019
• He3di3 3in 1out won't print from center of the bed

  1 view 6 comments 0 points Most recent by Guitar68 February 2019
• Connection problem

  1 view 10 comments 0 points Most recent by Repetier February 2019
• Repetier Host Freezing on startup

  1 view 4 comments 0 points Most recent by Repetier February 2019
• Dual Extruders won't Center

  1 view 8 comments 0 points Most recent by DJake February 2019
• SDCARDDETECT

  1 view 1 comment 0 points Most recent by Repetier January 2019
• Differen Steps/mm on dual extruders

  1 view 12 comments 0 points Most recent by Repetier January 2019
• Slic3r freezing windows 10

  498 views 12 comments 0 points Most recent by Repetier January 2019
• Printer heating extruder and idling

  1 view 1 comment 0 points Most recent by Repetier January 2019
• Repetier Host & Slic3r settings for BIBO 2 touch printer

  1 view 2 comments 0 points Most recent by Repetier January 2019
• Windows 10 1809 Backup

  1 view 0 comments 0 points Started by emmamillathompson January 2019
• How do I restart a print without homing again?

  1 view 6 comments 0 points Most recent by Repetier December 2018
• Problem Connecting Repetier Host to Printer

  1 view 3 comments 0 points Most recent by Dana December 2018
• Print stops after a few seconds

  1 view 4 comments 0 points Most recent by Repetier December 2018
• DaVinci 1.0A repetier firmware upgrade problems

  1 view 5 comments 0 points Most recent by SpiralSandwich November 2018
• Repetier Host 2.0

  801 views 26 comments 0 points Most recent by coosadog November 2018
• How o set new ZYX = 0 (home?)

  1 view 1 comment 0 points Most recent by Repetier November 2018
• Repetier host doesn´t show some lines on the preview, but prints fine

  1 view 1 comment 0 points Most recent by Repetier September 2018
• Open a file to the runiing repetier-host from command line

  1 view 1 comment 0 points Most recent by Repetier August 2018
• Serial Com Error Anycubic Kossel

  1 view 1 comment 0 points Most recent by Repetier August 2018
• connection issues

  1 view 7 comments 0 points Most recent by Repetier August 2018
• Error: Wrong checksum

  1 view 2 comments 0 points Most recent by SX500 August 2018
• Z probe settings

  1 view 12 comments 0 points Most recent by erniehatt August 2018
• compile problems

  1 view 28 comments 0 points Most recent by erniehatt July 2018
• Printer won't do anything

  1 view 2 comments 0 points Most recent by Kingdog July 2018
• Retraction Settings when Using Cura

  1 view 6 comments 0 points Most recent by Repetier July 2018
• Repetier says connected but bed and nozzle do not heat up

  1 view 1 comment 0 points Most recent by Repetier June 2018
• Upgrade 2.1.2. Configuration

  1 view 4 comments 0 points Most recent by Repetier June 2018
• Error when manually setting temp

  1 view 2 comments 0 points Most recent by Icarus June 2018