General

• @pause command, Server command in browser address line

  69 views 2 comments 0 points Most recent by Beach May 2017
• Auto start print from S3D

  105 views 11 comments 0 points Most recent by cbusillo March 2017
• Unable to print gcode with velocity painting

  151 views 3 comments 0 points Most recent by dot_bob March 2017
• Second Camera doesn't Work on Raspberry Pi B+

  69 views 6 comments 0 points Most recent by geoffreyforest March 2017
• Lost Repetier server pro license

  615 views 3 comments 0 points Most recent by Repetier February 2017
• RepHost upload to server issues

  23 views 1 comment 0 points Most recent by Repetier February 2017
• Constantly losing wifi connection with RP3

  58 views 2 comments 0 points Most recent by pscartozzi February 2017
• Adding a g-code dropbox to rasberry Pi

  49 views 2 comments 0 points Most recent by Taxus812 February 2017
• Anyone seeing layer count in print list always at 0

  111 views 8 comments 0 points Most recent by jvince February 2017
• Change IP Address

  129 views 3 comments 0 points Most recent by Repetier January 2017
• Rendered images looks different, server vs host.

  47 views 5 comments 0 points Most recent by Repetier December 2016
• 80.1 v4 PRints FAILING mid print.

  63 views 5 comments 0 points Most recent by Repetier November 2016
• Need help reading Temperature in Raspbian

  44 views 2 comments 0 points Most recent by ignis November 2016
• key

  52 views 1 comment 0 points Most recent by Repetier November 2016
• Prints randomly failing using Repetier-Server but not Repetier-Host

  71 views 1 comment 0 points Most recent by Repetier October 2016
• Firmware Update via Server + DUE

  132 views 2 comments 0 points Most recent by errolt October 2016
• GCode beim Verbinden läuft zweimal

  54 views 2 comments 0 points Most recent by FloPiep September 2016
• Error in Booting to Touchscreen Guide

  52 views 1 comment 0 points Most recent by Repetier September 2016
• Compile error for default firmware

  72 views 2 comments 0 points Most recent by graybeardtx September 2016
• Check for update or fresh install

  62 views 1 comment 0 points Most recent by Repetier August 2016
• Adding new printer doesn't add/detect extruder

  75 views 1 comment 0 points Most recent by Repetier July 2016
• Pasting this fro the Q A section so someone will hopefully respond

  54 views 3 comments 0 points Most recent by pscartozzi July 2016
• Problem to start printing

  200 views 6 comments 0 points Most recent by gwolfsystems July 2016
• Install error on Ubuntu 14.04LTS 64 bit

  389 views 5 comments 0 points Most recent by Repetier May 2016
• costom delta calibration problems

  83 views 0 comments 0 points Started by hvashist April 2016
• Roll back from 0.75 to 0.70.1?

  124 views 3 comments 0 points Most recent by errolt April 2016
• start repetier service dosent work for me

  157 views 1 comment 0 points Most recent by Repetier January 2016
• Setting up a Printer Lab

  199 views 2 comments 0 points Most recent by Andy_in_Indy November 2015
• Using at execute (@execute) commands

  742 views 11 comments 0 points Most recent by Kissell August 2015
• Import setting from Repetier Host

  2.5K views 7 comments 0 points Most recent by Repetier January 2015