CuraEngine

• slicer G code always sets fan to 50% S127 no matter the fan setting

  1 view 12 comments 0 points Most recent by Repetier November 9
• es Funktioniert einfach nicht mit Cura 5.2.1

  1 view 2 comments 0 points Most recent by marcus_w November 4
• Resolution other than 0.2???

  1 view 2 comments 0 points Most recent by Repetier October 17
• wall espesor

  1 view 0 comments 0 points Started by martinchoj3 June 14
• Support for Ironing

  1 view 1 comment 0 points Most recent by Repetier June 3
• Looking for clarifications on retraction settings and behavior (CuraEngine / Host)

  1 view 6 comments 0 points Most recent by P_O May 14
• Is a flattened Skirt possible with CuraEngine/Host ?

  1 view 2 comments 0 points Most recent by P_O May 13
• Mindesttemperatur Düse 240 Grad

  1 view 7 comments 0 points Most recent by SiaEnder3 April 29
• Repetier einbinden geht nicht.

  1 view 4 comments 0 points Most recent by Phrayzur March 22
• Ender 5 plus und Pause at layer

  1 view 2 comments 0 points Most recent by Snippy30 March 6
• Using @execute to energize an external relay

  1 view 2 comments 0 points Most recent by Lawrence February 28
• Where is the "wall thickness" setting in CuraEngine?

  1 view 3 comments 0 points Most recent by Repetier January 2
• Shifted Infill lines with curaengine

  1 view 1 comment 0 points Most recent by Repetier December 2021
• Temperatuur extruder.

  1 view 1 comment 0 points Most recent by Repetier_Support July 2021
• PET G Settings

  1 view 0 comments 0 points Started by DBSDBS May 2021
• Kein Boden und Deckel nach dem slicen

  1 view 15 comments 0 points Most recent by cyberman April 2021
• Vorpump-Turm

  1 view 2 comments 0 points Most recent by Werner058 April 2021
• Vorpump-Turm

  1 view 0 comments 0 points Started by Werner058 April 2021
• Adhesion type "None" still creates brim

  1 view 5 comments 0 points Most recent by dkota March 2021
• Launch Ultimaker Cura when slicing and not just the Curaengine?

  1 view 1 comment 0 points Most recent by Repetier March 2021
• restart after killing a print

  1 view 2 comments 0 points Most recent by sapper January 2021
• Problema durante la stampa del perimetro esterno /interno

  1 view 0 comments 0 points Started by Marco52 January 2021
• Best settings tweaks to create a better top layer.

  1 view 4 comments 0 points Most recent by Repetier January 2021
• Repetier generates wrong GCodes

  1 view 1 comment 0 points Most recent by Repetier November 2020
• How can I adjust the "extrusion multiplier"?

  1 view 11 comments 0 points Most recent by armega October 2020
• Any idea when Repetier will support the newest version of CuraEngine?

  1 view 1 comment 0 points Most recent by Repetier September 2020
• Unknown command: -p

  1 view 9 comments 0 points Most recent by Repetier September 2020
• Calibration cube with PLA and PETG. PETG is off 0.6mm in Y direction and 0.3 in X direction. Z is ok

  1 view 3 comments 0 points Most recent by Repetier September 2020
• Cura doesn't use settings

  2.7K views 19 comments 0 points Most recent by Repetier August 2020
• importing settings from other versions of Cura

  1 view 2 comments 0 points Most recent by raymw July 2020