recoush

Discussions

• MKS Gen L 2.1 Change out the net A8 converted to MKS and Repetier Firmware the EO Direction issue

  1 view 1 comment 0 points Most recent by recoush July 15Extruder & Bed
• issue using config tool either 92 or 1.0

  1 view 3 comments 0 points Most recent by Repetier March 25Extruder & Bed
• Controller boards 32 bit

  1 view 2 comments 0 points Most recent by recoush March 18Motherboard
• Multiple (3) Z steppers with 3 drivers leadscrews Want to Install a Z Inductive prox Bltouch etc.

  1 view 2 comments 0 points Most recent by recoush March 17Repetier-Firmware
• Print Stops and Heater shuts down, when moving from Home position toward print position

  1 view 4 comments 0 points Most recent by recoush November 2023General
• Heater extruder temperature decoupling

  1 view 13 comments 0 points Most recent by recoush January 2023General
• ramps 1.4 issue with 3 extruder motors

  1 view 4 comments 0 points Most recent by recoush November 2022General
• MKS Gen L 2,1

  1 view 7 comments 0 points Most recent by recoush January 2023General
• printing with server proG-code error with M539?

  1 view 13 comments 0 points Most recent by Repetier November 2022General
• CoreXY moved endstops 24.5mm on X and Y Min endstop bounce and Jitter

  1 view 2 comments 0 points Most recent by recoush September 2022Motor Control
• zprobe Activity

  1 view 3 comments 0 points Most recent by Repetier February 2019Extruder & Bed
• extruder / part cooling Fan

  1 view 6 comments 0 points Most recent by recoush February 2019General
• configuration tools drive systems

  1 view 2 comments 0 points Most recent by recoush October 2018Questions & Answers
• how to extrude filiment along an axis?

  1 view 2 comments 0 points Most recent by recoush July 2018Extruder & Bed
• ramps 1.4 to MKS Gen l

  1 view 0 comments 0 points Started by recoush April 2018 Repetier-Firmware
• Temperature issue Thermistors?

  1 view 1 comment 0 points Most recent by Repetier December 2017Extruder & Bed
• 4.9K thermistor ? on Diamond hot end

  1 view 1 comment 0 points Most recent by recoush December 2017General
• radds 1.5 display and board type

  30 views 4 comments 0 points Most recent by recoush February 2019General
• Ramps 1.4 thermistor pcb repair

  26 views 4 comments 0 points Most recent by recoush October 2017General
• printing not smooth more like pin heads.

  33 views 2 comments 0 points Most recent by recoush September 2017Extruder & Bed
• baud rates cant change

  33 views 5 comments 0 points Most recent by recoush September 2017General
• running from sd card

  29 views 2 comments 0 points Most recent by recoush September 2017General
• mirror imaging of printing words

  53 views 9 comments 0 points Most recent by recoush September 2017Extruder & Bed
• which motherboards support 3 extruders

  61 views 2 comments 0 points Most recent by recoush September 2017Motherboard
• duial extruder iis hitting table

  63 views 7 comments 0 points Most recent by recoush September 2017Extruder & Bed
• dual extruders temps sensors 0 & 1

  56 views 8 comments 0 points Most recent by recoush August 2017Extruder & Bed
• after starting server 0.86 and loging out now wont connect to Host

  34 views 7 comments 0 points Most recent by recoush August 2017Questions & Answers
• calibration of XY after printing

  37 views 1 comment 0 points Most recent by Repetier August 2017Motor Control
• extruding around the X and Y perimeter

  15 views 0 comments 0 points Started by recoush August 2017 Extruder & Bed
• slicer extrusion g code

  73 views 9 comments 0 points Most recent by recoush August 2017Extruder & Bed
More Discussions