recoush
scratch built an 8020 frame large scale Corexy 3D printer with 3 Z motors and 3 extruders using only Repetier SW
About
- Username
- recoush
- Joined
- Visits
- 182
- Last Active
- Roles
- Member
Comments
-
Found it :>) in config H extruder 1 Inverse 0 changed to 1 Working :>)
-
went back to my 2022 files and copied in Pins. H and the new Configuration h file into the Repetier Folder and that fixed the Config H issues compile and upload worked , luckily i keep backups Whew :>) recoush
-
Wondering, with 3 Extruder (E0, E1, E2) same temp zero sensor and same Heater E0 and if having all the same for each should be E1 and e2 Different? EXT0_TEMPSENSOR_TYPE 1#define EXT0_TEMPSENSOR_PIN TEMP_0_PIN#define EXT0_HEATER_PIN HEATER_0_PIN#defi…
-
Ok thank you for the Fast answer much appreciated recoush
-
Ok excellent Thank you! Recoush
-
definably some connection to the extruder fan being on or OFF :>) Well it turns out my heatblock to heatbreak was leaking filament. Noticed yesterday the heatblock was covered in filament and my prints where significantly changed to barely printi…
-
Repetier host 2.3.2 Windows 10 Laptop primary, Win10 Desktop Backup, used pid autotuned for pla 200 and Petg 240 and their does appear to be a little over temp going on which maybe causing the cutoff, just really weird that turning on the extruder f…
-
Yes, That worked my prints and Extruder temperature are back to Normal. Makes sense since i changed to higher wattage heater :>) thank You Recoush
-
Ran this routine after reading anther autotune Pid M303 P0 S250 X0 R10 C1 results KP1.72 KI0.06 KD 30.31 If i read this program sequence correctly it seems to have autosave to Eeprom recoush
-
autotuned came up with this M303 E0 S250 C10 results KP2.42 Ki 0.02 KD20.83 2nd pass just m303 KP2.54 KI0.08 KD20.31 Looks real close
-
So successfully update with Repetier using the ramps 1.4 routine. I am waiting to update the cpu until after making some more adjustments due to some minor glitches with my replacement ramps 1.4 the old one was 5 years old so verifying operational …
-
actually doing that now :>) Of course this after the fact. My most recent prints have been failing, seems to overshoot then undershoot then decouple after having started printing. So i am being super hopeful that the auto tune, helps fix this…
-
Switched to bang-bang also set max pid to 225 from 255 left decoupling max hold at 35 and pid control range at 40 very little change still overshoots as long as the alarm is not re-occurring. going to keep testing to see what if anything drops th…
-
agree, set at 250 C (PetG) the overshoot was 30C 281C then dropped back down. The 35C is just high enough for the overshoot going to re configure with the tool when i Have some more time to test :>)
-
played with this value up to 80, still same result. Changed it back to 40 Looked into the config tool version 1.xx and found this item DECOUPLING_TEST_MAX_HOLD_VARIANCE=20 C said, mine being over by at least 35 Degree C changed this to 35 Degre…
-
Excellent Will give that a check and set (Tests) sound like the place to start :>) found it was set @20 changed, Now set @40 Thank you much appreciated
-
adding initial or 1st power on is always an overrun and requires an acknowledgement. subsequent new prints after the initial power on overrun are ie 2nd 3rd usually over runs, but at 266 starts then starts to drop back down to the 230 setpoint
-
Excellent, Uploaded without any issues my existing firmware to the MKS Gen L 2.1 completed no errors, started installing new drivers since the old ones are 5 years old keeping for spares. need to hook up some motors and extruders and see how work…
-
have to make a note might be useful for mixing have to use the o;d ramps the new amega 2560 i got was bad returning for an exchange at least this 5 year old setup still working Saved my config h and Pins H in a separate folder, seems like a good …
-
Single nozzle E3D J with 65w Heater (did have 3 J at one time) plan was for a 3 head diamond. Currently only using one single hot end nozzle and choose one extruder motor (0.1.2) also parts cooling fans an hot end fan of the one fan control conf…
-
I would say Design is first then consider, Design type delta Corexy other Cartesian what do you intend to print? (how big will you need the Bed) material i.e Filament what type will you print (will you need a heated bed?) Building your own or buyi…
-
Same Setup as the ramps Work as intended? I know they are very similar any potential issues having to change Pins etc..
-
this seems to be the issue, as i just found an old internet search where this was explained( internet search a good thing) this is starting to make sense when i installed the new Arduinos .19 everything was deleted. or maybe the Repetier firmware…
-
downloaded the latest Arduino 1.8 .19 nothing complies? tried all the configurator tool 91 92 .1.01? comes up with all sorts of issues some of the issues below tried downloading all files after configurator tool and tried just config H decoupling…
-
If memory issue maybe the programs files, i will try to find a smaller size file and then try a larger file. thank you much appreciated
-
Working for 5 years only change was the higher wattage heater and from a typ1 1 to type 11 thermistor guess it is time to upgrade, either the Radds 1.5 and The one i want to use is MKS genL 2.1 (nice everything on one board ) but i don't see anythi…
-
Recv:13:44:04.276: ok 716Recv:13:44:05.247: ok 717Recv:13:44:06.253: waitRecv:13:44:06.257: ok 718Recv:13:44:07.288: ok 719Recv:13:44:08.298: ok 720Recv:13:44:09.280: waitRecv:13:44:09.284: ok 721Recv:13:44:10.310: waitRecv:13:44:10.310: ok 722Recv:…
-
Humm Ok was hopeful the M539 was the issue my setup is a Corexy with 3 extruders drivers as main mixing 1 heater block choosing an extruder motor one of the three I actually have an Multiplexer board which allows upto 6 different extruder motors usi…
-
jitters basically it just bounces in one spot stops moving but is trying to move. went back and pulled the X & Y reprap switches , at first i thought i had a corrosion problem was just very dirty and found the copper exsposéd the other one loo…
-
well then , may have to use an endstop and not D59 which is Aux2 guess i have to do more research that's why we test :>) thanks Recoush