Questions & Answers

• Repetier Host Enqueueing "G28", "G29", "G1 Z3" Commands in middle of Gcode for Unknown Reason

  1 view 3 comments 0 points Most recent by Repetier October 2018
• mix g1 avec spinter

  1 view 1 comment 0 points Most recent by Repetier September 2018
• message d erreur

  1 view 1 comment 0 points Most recent by Repetier September 2018
• Printer not moving full distance of print bed...

  1 view 1 comment 0 points Most recent by Repetier September 2018
• CoreXY with Cartesien DIR and STEP output

  1 view 7 comments 0 points Most recent by smeric August 2018
• Firmware CoreXY + DualX help

  1 view 8 comments 0 points Most recent by Repetier July 2018
• Connection problem

  1 view 3 comments 0 points Most recent by Repetier July 2018
• Connection Lost?

  1 view 14 comments 0 points Most recent by Repetier July 2018
• Repetier-Firmware для версии 1.0.2 tmc2130 mega2560+ramps1.4

  1 view 3 comments 0 points Most recent by Repetier July 2018
• Print not sticking flow rate

  1 view 2 comments 0 points Most recent by 156801 June 2018
• Extruder wont heat or extrude

  1 view 1 comment 0 points Most recent by Repetier May 2018
• Homing settings @ zero. Extruder zips all over on run.

  1 view 3 comments 0 points Most recent by Repetier April 2018
• mobiler zugriff

  1 view 3 comments 0 points Most recent by Repetier March 2018
• How Can I achieve Continuous SPI Master Clock from PIC SPI?

  1 view 0 comments 0 points Started by Paullo March 2018
• print start height

  1 view 2 comments 0 points Most recent by Repetier March 2018
• G92 does nothing

  1 view 1 comment 0 points Most recent by Repetier February 2018
• Object not appearing

  1 view 1 comment 0 points Most recent by steveKimpton February 2018
• Who is in control - Repetier Host or CURA

  1 view 10 comments 0 points Most recent by Repetier February 2018
• Cura not slicing

  1 view 1 comment 0 points Most recent by Repetier February 2018
• Control RGB LED strip (common anode)

  215 views 3 comments 0 points Most recent by Repetier January 2018
• change direction of y axis +/-

  1 view 4 comments 0 points Most recent by Repetier January 2018
• Use of Repetier for simple status check

  1 view 5 comments 0 points Most recent by Repetier January 2018
• Just starting out and trying to get things working

  1 view 11 comments 0 points Most recent by Repetier December 2017
• FEATURE_TWO_YSTEPPER

  1 view 8 comments 0 points Most recent by Mane660 November 2017
• Using 3D printer to deposit etch resist for PCB prototyping

  319 views 11 comments 0 points Most recent by Raishin September 2017
• Z probe not working

  72 views 4 comments 0 points Most recent by myfacelackseyes August 2017
• Can any one get repetier working or not? why no fixs?

  58 views 1 comment 0 points Most recent by Repetier July 2017
• Serial Port Gone

  47 views 1 comment 0 points Most recent by Repetier December 2016
• RepRapDiscount Full Graphic Smart Controller

  152 views 8 comments 0 points Most recent by eeerfan December 2016
• the abs retract too much

  27 views 1 comment 0 points Most recent by Repetier November 2016