Display & Keyboard

• A guide to add a simple menu?

  893 views 15 comments 0 points Most recent by AndreasMaeder September 2016
• Showing chamber temperature into LCD display instead of Extruder 2, how to

  233 views 7 comments 0 points Most recent by Paranoid August 2016
• Wrong letters on display

  56 views 2 comments 0 points Most recent by PetBel August 2016
• Need help on custom logo on lcd when starting up.

  972 views 5 comments 0 points Most recent by Getget July 2016
• Radds LCD goes Blank after longer printting time

  229 views 3 comments 0 points Most recent by xnaron July 2016
• Viki 2 support ?

  79 views 2 comments 0 points Most recent by Repetier June 2016
• DUE with I2C SSD1306 crash on EEPROM write.

  318 views 7 comments 0 points Most recent by Repetier June 2016
• Gcode to update status line in full graphics LCD?

  147 views 1 comment 0 points Most recent by Repetier May 2016
• One Click run from SD card

  124 views 5 comments 0 points Most recent by Repetier May 2016
• Megatronics 2.0 on board SD card and smart LCD

  628 views 3 comments 0 points Most recent by Paranoid May 2016
• add menu calibrate tower

  122 views 0 comments 0 points Started by maralb May 2016
• Melzi+ reprap smart controller

  133 views 2 comments 0 points Most recent by totosse May 2016
• Custom Buttons with UI_KEYS_BUTTON_HIGH/LOW

  510 views 13 comments 0 points Most recent by RAyWB April 2016
• PanelDue - no signal from board

  201 views 3 comments 0 points Most recent by paulhut April 2016
• Time of printing

  498 views 9 comments 0 points Most recent by Repetier April 2016
• LCD i2c - how the lcd should behave right after uploading firmware?

  310 views 4 comments 0 points Most recent by dev March 2016
• RepRapDiscount Full Graphic on a Megatronics 3.0 -> all pixel on

  547 views 7 comments 0 points Most recent by Repetier March 2016
• SD-Card Error

  801 views 5 comments 0 points Most recent by Scotty March 2016
• Da Vinci 1.0: Not displaying anything on the screen.

  153 views 0 comments 0 points Started by intelzee March 2016
• Set To Origin

  277 views 1 comment 0 points Most recent by Repetier March 2016
• Full Graphic Smart Controller Encoder Problem

  537 views 2 comments 0 points Most recent by Semml March 2016
• Display change not compiling

  126 views 2 comments 0 points Most recent by mrk February 2016
• MKS Gen-2z v1.1/Ramps 1.4/A4988 on Prusa i3 with LCD2004A display

  520 views 1 comment 0 points Most recent by Repetier January 2016
• SD init fail using RepRapDiscount Full Graphic Smart Controller in Repetier 0.91/0.92

  2.9K views 4 comments 0 points Most recent by FireflyNJ January 2016
• 7-segment display MAX72XX SPI Hardware

  165 views 4 comments 0 points Most recent by Agge December 2015
• Custom Menu

  565 views 9 comments 0 points Most recent by Repetier December 2015
• Ramps 1.4 And Full Graphic Smart Controller SD card Issue

  577 views 2 comments 0 points Most recent by mattr254 November 2015
• How configure LCD20x4 i2c Chip PCF8574

  242 views 1 comment 0 points Most recent by Repetier November 2015
• Case light pin in 0.92.4. - how to do it?

  663 views 7 comments 0 points Most recent by Monokai September 2015
• SD card inserted!

  361 views 1 comment 0 points Most recent by Repetier August 2015