Bug Reports

• Configuration of extcommands.xml and so on are missing after update to 0.92.3

  1 view 3 comments 0 points Most recent by Repetier December 2019
• In Summary the filament used is not saved correctly

  1 view 1 comment 0 points Most recent by Repetier November 2019
• Repetier-Server Pro 0.93.0, Camera view size too big

  1 view 1 comment 0 points Most recent by Repetier November 2019
• Pi Image .92.1 Acces Point Problem

  1 view 4 comments 0 points Most recent by Repetier November 2019
• Configuration Tool Bug: PARK_POSITION_Y is PARK_POSITION_Z_RAISE not input box value

  1 view 1 comment 0 points Most recent by Repetier November 2019
• Der untere Zip Upload Butten funktioniert nicht

  1 view 1 comment 0 points Most recent by Repetier November 2019
• Double printing from repieter server

  1 view 9 comments 0 points Most recent by Repetier October 2019
• Falsche ETA Angabe

  1 view 1 comment 0 points Most recent by Repetier October 2019
• @execute in 0.92

  1 view 18 comments 0 points Most recent by Repetier October 2019
• Individual printer interface loads oddly/fails to load.

  1 view 1 comment 0 points Most recent by Repetier October 2019
• Druck bricht ab

  1 view 3 comments 0 points Most recent by Repetier October 2019
• Fehler bei Vorschaubildern nach Update von 0.92.1 auf 0.92.2

  1 view 6 comments 0 points Most recent by Jannek October 2019
• camera on raspi not work

  1 view 4 comments 0 points Most recent by user September 2019
• RPi v0.92.2 not properly recovering/reconnecting after hard firmware halt/reset

  1 view 6 comments 0 points Most recent by Repetier September 2019
• Repetier-Server upgrade from xx.1 to xx.2

  1 view 2 comments 0 points Most recent by malcinator September 2019
• Calibration Z Repetier geht nicht aus der Funktion ( Eieruhr dreht weiter) Felix Pro

  1 view 3 comments 0 points Most recent by hardy123 September 2019
• G-Code ausschließen

  1 view 3 comments 0 points Most recent by Repetier September 2019
• Update 0.92.1 no screen to PI

  1 view 2 comments 0 points Most recent by Franckperes September 2019
• Exclude G-Codes

  1 view 3 comments 0 points Most recent by Repetier September 2019
• Firmware upload on Arduino 2 it doesn't work on Repetier Server V0.92.1 (SOLVED)

  1 view 3 comments 0 points Most recent by Repetier August 2019
• Flickering LCD & errors on console (Prusa MK2S and Repetier Server Pro v0.92)

  1 view 1 comment 0 points Most recent by BiSProps August 2019
• can't upgrade from 0.91.2 to 0.92.0

  1 view 1 comment 0 points Most recent by Repetier August 2019
• Webinterface zeigt nichte alle Zeilen des Logs an

  1 view 1 comment 0 points Most recent by Repetier July 2019
• V2.0.5 Repetier host freezes

  1 view 1 comment 0 points Most recent by Repetier July 2019
• Image for Raspberry PI 3 Repetier server 0.80.1 cannot connect to WLAN

  926 views 26 comments 0 points Most recent by Repetier June 2019
• Extrusion stops with flow setting below 100%

  1 view 4 comments 0 points Most recent by maan June 2019
• Verbindungsprobleme

  1 view 21 comments 0 points Most recent by raabi June 2019
• Touch UI - CSS Media Ranges

  1 view 1 comment 0 points Most recent by Repetier June 2019
• LCD

  1 view 15 comments 0 points Most recent by Repetier May 2019
• Calling External Commands is not working from gcode

  402 views 6 comments 0 points Most recent by Repetier May 2019