RepetierSupport
About
- Username
- RepetierSupport
- Joined
- Visits
- 143
- Last Active
- Roles
- Administrator
Comments
-
Du hast Recht, da hat sich ein Fehler eingeschlichen. Die Aufnahmen werden gemacht, in der aktuellen Version wird aber die Registerlasche mit den Aufnahmen nicht angezeigt. Wir korrigieren es für das nächste Update. Du kannst dir bis dahin mit der m…
-
Thanks for the tip, I have revised the instructions, should now fit.
-
Did you activate HTTP and Straming in Yawcam? Do you use the correct ip addresses and ports? I just tried it an it works fine. Wen you want to see the webcam in Repetier-Server, Yawcam has to run.
-
Maybe this can help you: https://www.repetier-server.com/knowledgebase/multiple-printers-printer-farm/
-
In this case, please contact the seller at: https://www.mycommerce.com/shopper-support/
-
Here is the image: https://imgur.com/aS6RRiK Temperatures are not stored in log files.
-
Do you have a Pi Zero W and did you set up wifi on the Pi Zero?
-
This can help: https://www.repetier-server.com/knowledgebase/autoupdate-update-fails/
-
Hi Palmerr, thanks for your help, I have updated your page with the new file.
-
Thanks a lot for this hint. I have added this to our docs: https://www.repetier-server.com/using-simplify-3d-repetier-server/
-
You can set the color int Global Settings -> Preview Images. If you change this before uploading the G-Code, the new color will be used.
-
You will get the Extruders you select in Repetier-Host, so you get what you see. Just the support extruder is set by Slic3r. Perimeters are only used for skirt. This requires Version 1.5.5 to work correctly.
-
I'm sorry but I could not reproduce your error, I also downlöoaded the skull for my test. Does this happen with every model or just with this skull?
-
Hi, the G-Code does not get alteres, I think that it was accident.
-
We are very busy with other projects like Repetier-Server (http://www.repetier-server), which runs also on Mac, so that we can not give any times.
-
No, we have not stopped it, but other parts have at the moment a higher priority.
-
Sorry, but it will take time, but it will come.
-
That problem seems to be fixed with latest 0.92.2 firmware. Just update.
-
The controls should not allow negative coordinates, that is below print plate and should be prevented. If you really need it just send the gcode, e.g. G1 Z-1 F100
-
No thermistor - no heatup. Will be detected as missing and for safety it will disable heating. You see this also in the log files.
-
You need to power the servo pins. See RAMPS pin definition in www.reprap.org ramps description. It is near the 4 servo pins. This should be a poer source having enough power to run the servos! So don't take it from the arduino directly. Pin numbers …
-
Can you post a screenshot. I have only had this when the other 3/4 were out of printing table.
-
On newer Mac versions deleting the plist is not a solution as OS X will restore old content from cache, Use instead defaults delete repetier.Repetier-Host-Macto start with fresh settings.
-
On newer Mac versions deleting the plist is not a solution as OS X will restore old content from cache, Use instead defaults delete repetier.Repetier-Host-Macto start with fresh settings.
-
Output bed is taken from M105 response @B:255 for example. If the used firmware does not contain this you will see no output as the host does not know how much is used.
-
Nice idea, will see if I get the time.
-
I had this very seldom. In 0.51.1 I had changed some parts which hopefully avoid this. I didn't seen it since then, so which version was in use when it happened? Normally restarting the server helps.
-
Did you install a printer driver?
-
Right click on program icon -> Properties -> CompatibilityMark Disable scaling on high DPI
-
Yes, that is no problem.