Tips & Tricks

• Ultimaker 2+ LED Lights on/off does not work/ different implementation

  1 view 1 comment 0 points Most recent by Repetier June 20
• Sicherheitsabfrage zu Druckbegrenzung

  1 view 9 comments 0 points Most recent by Repetier June 5
• Send notification to IFTTT on job status

  1 view 1 comment 0 points Most recent by Repetier May 22
• Welcher Touchscren ist zu emphelen

  1 view 6 comments 0 points Most recent by Repetier April 18
• Group of Printers

  1 view 6 comments 0 points Most recent by Repetier April 7
• GPIO-PIN anhand Temperatur von Raspi CPU setzen?

  1 view 2 comments 0 points Most recent by Maga February 14
• Configuration of WaveShare 3.5inch display (C)

  1 view 0 comments 0 points Started by Hauke February 13
• Skript wird nicht ausgeführt ... Finde keinen Fehler

  1 view 8 comments 0 points Most recent by Repetier January 30
• Verbindung zum Drucker

  1 view 2 comments 0 points Most recent by bjoernba25 December 2020
• Filament Sensor

  1 view 2 comments 0 points Most recent by 9steff2 December 2020
• Mehrere Kameras am Repetier Server

  1 view 0 comments 0 points Started by Mavericklp November 2020
• "Pause and Resume" Printer with Light Sensor Data

  1 view 12 comments 0 points Most recent by Repetier September 2020
• Upload to repetier from slic3r prusa edition

  1 view 56 comments 0 points Most recent by Benzolio August 2020
• Access through SAMBA and use Project folder and uploader folder throught NETWORK drive.

  1 view 1 comment 0 points Most recent by dkSwe August 2020
• Installation of Waveshare 3.5" (non-HDMI) LCD display / touchscreen on Raspberry Pi

  1 view 10 comments 0 points Most recent by pcpayn3 July 2020
• Best Practices When Upgrading Repetier-Server Raspberry Pi Image

  1 view 3 comments 0 points Most recent by armega July 2020
• Disconnecting kernal: reset high-speed USB device

  1 view 18 comments 0 points Most recent by Repetier April 2020
• Set z offset 3d printer

  1 view 3 comments 0 points Most recent by Repetier April 2020
• GPIO INPUT/OUTPUT CONTROL

  1 view 5 comments 0 points Most recent by michi_appiani March 2020
• Voice controlled 3D printer with Google Assistant

  155 views 3 comments 0 points Most recent by AndreCordeiro November 2019
• Restart repetier-server and klipper use extcommands

  1 view 1 comment 0 points Most recent by Repetier September 2019
• lua exaples

  1 view 1 comment 0 points Most recent by Repetier June 2019
• Setting up Adafruit 3.5" TFT w/ Repetier Server

  1 view 7 comments 0 points Most recent by WOOKIE111 April 2019
• Settings of REPETIER

  1 view 1 comment 0 points Most recent by Repetier February 2019
• Controlling PiTFT Plus 3.5" 480x320 backlight

  1 view 0 comments 0 points Started by mcmatrix December 2018
• Looks goog but not right

  1 view 20 comments 0 points Most recent by Felipelando October 2018
• Local touchscreen on printer ?

  91 views 2 comments 0 points Most recent by vincen August 2017
• Alternate French translation for Repetier-Server 0.80.3 (Raspberry Pi version)

  72 views 3 comments 0 points Most recent by vincen August 2017
• Stop RS boot into Pi prompt

  80 views 1 comment 0 points Most recent by Repetier December 2016
• Printer Going cold, losing X/Y Location... Double check alternative server.

  88 views 0 comments 0 points Started by Zeepro July 2016