Bug Reports

• Server lässt sich nach ca. drei Tagen Laufzeit nicht mehr über das Netzwerk verbinden

  1 view 2 comments 0 points Most recent by 3DPrintMunich April 2021
• UI cut off when long filename is used

  1 view 1 comment 0 points Most recent by Repetier April 2021
• Saving from host to server is a problem after upgrading to 1.0

  1 view 8 comments 0 points Most recent by Repetier April 2021
• Corrupted Prints

  1 view 18 comments 0 points Most recent by NickRno77 April 2021
• LastPrintingTime

  1 view 1 comment 0 points Most recent by Repetier April 2021
• general problem with determining print temperature

  1 view 3 comments 0 points Most recent by Repetier April 2021
• Arrêt brutal durant l'impression

  1 view 28 comments 0 points Most recent by docman95 April 2021
• No reconoce la impresora en el servidor ( raspberry pi )

  1 view 1 comment 0 points Most recent by Repetier April 2021
• Z-axis does not move if move down on touchscreen interface is pressed (V1.0.4)

  1 view 3 comments 0 points Most recent by Repetier March 2021
• Repetier-Server 1.0.0. oder 1.0.1 mit der MMU2S im Single Modus

  1 view 28 comments 0 points Most recent by 3D_Drehzahl73 March 2021
• Wrong layers number when import some gcode

  1 view 3 comments 0 points Most recent by Repetier March 2021
• Sort with generated time

  1 view 1 comment 0 points Most recent by Repetier March 2021
• Messages Disapear in Browser

  1 view 8 comments 0 points Most recent by W4tel_BiDi March 2021
• Webcam geht nach kurzer Zeit aus

  1 view 3 comments 0 points Most recent by Repetier March 2021
• Marlin 2.0.x Line numbers

  1 view 10 comments 0 points Most recent by mcpovel March 2021
• 1.0.4. Mac temperature stops updating

  1 view 1 comment 0 points Most recent by wildfang March 2021
• Webcam appears to not work with .local URL

  1 view 4 comments 0 points Most recent by AngryDad March 2021
• Marlin progress out of sync

  1 view 5 comments 0 points Most recent by Repetier March 2021
• Hilfe Heizbett heizt auf 90 Grad

  1 view 6 comments 0 points Most recent by Repetier March 2021
• G4 issue?

  1 view 1 comment 0 points Most recent by Repetier March 2021
• 1 heater 2 extruder = 2 header werden angezeigt

  1 view 5 comments 0 points Most recent by Repetier March 2021
• Extruder 33

  1 view 1 comment 0 points Most recent by Repetier February 2021
• Reports werden nicht angezeigt.

  1 view 2 comments 0 points Most recent by juergen963 February 2021
• Kann meinen Drucker nicht verbinden

  1 view 1 comment 0 points Most recent by Repetier February 2021
• Server 1.0.3 - Wildly inaccurate ETA calculations

  1 view 4 comments 0 points Most recent by Repetier February 2021
• Klipper: show wrong temperate when select T1 (shared extruder)

  1 view 23 comments 0 points Most recent by Marco67 February 2021
• Bug in Repetier-Host nach Update Repetier-Server auf 1.0.0 u. 1.0.1

  1 view 5 comments 0 points Most recent by Sio_x February 2021
• wrong icons on the web-host

  1 view 1 comment 0 points Most recent by Repetier February 2021
• Lizenz-Deaktivierung nicht möglich

  1 view 1 comment 0 points Most recent by Repetier February 2021
• error starting monitor

  1 view 3 comments 0 points Most recent by Repetier February 2021