Questions & Answers

• Auto bed levelling vs distortion correction

  265 views 1 comment 0 points Most recent by Repetier January 2016
• Print quality test generator

  265 views 2 comments 0 points Most recent by Dksre January 2016
• Plugin Remove tabs/menus etc..

  64 views 1 comment 0 points Most recent by Repetier January 2016
• geeetech GT2560

  3.5K views 6 comments 0 points Most recent by MShievitz January 2016
• PAUSE button

  129 views 1 comment 0 points Most recent by Repetier January 2016
• print object size bigger then 3d model object size

  223 views 4 comments 0 points Most recent by rlyt123456 December 2015
• Extruder won't go while printing, works through manualcontrol though

  1K views 2 comments 0 points Most recent by Imaginators December 2015
• SD card print

  263 views 2 comments 0 points Most recent by fantasiiio December 2015
• Repetier manual Control movments?

  314 views 4 comments 0 points Most recent by Repetier December 2015
• How do I improve print quality on the underside?

  178 views 2 comments 0 points Most recent by dislegal December 2015
• Controlling the extruder`s direction

  517 views 1 comment 0 points Most recent by Repetier November 2015
• M999...im gonna lose my mind

  82 views 1 comment 0 points Most recent by Repetier November 2015
• problem with getting my xyz/home situated

  13.5K views 21 comments 0 points Most recent by PixelPusher October 2015
• Repetier Host manual control for extruder issue

  2.2K views 13 comments 0 points Most recent by Repetier October 2015
• Davinci xyz anything higher than 5mm starts to click and will not extrude, not a clog, not bed level

  906 views 9 comments 0 points Most recent by Repetier October 2015
• I cannot get extruder temp above 180, why?

  279 views 4 comments 0 points Most recent by PixelPusher October 2015
• Own commands defined - Problems with sending them trough Repetier-Host

  147 views 2 comments 0 points Most recent by Repetier September 2015
• Plugin filament color

  94 views 1 comment 0 points Most recent by Repetier September 2015
• Z Axis steps per mm: 80?

  224 views 3 comments 0 points Most recent by Repetier September 2015
• DaVinci Missing Line Detected - Correcting Buffer Useage

  442 views 2 comments 0 points Most recent by Tish86 September 2015
• Z axis and retracting

  1.3K views 8 comments 0 points Most recent by Repetier August 2015
• Unable to find an entry point named 'glGenBuffers' in DLL 'opengl32.dll'.

  1.6K views 4 comments 0 points Most recent by Repetier August 2015
• Unknown rows in Configuration.h

  1.5K views 2 comments 0 points Most recent by DBSDBS August 2015
• Repetier-Host Plugin - totalfiamentUsed

  229 views 2 comments 0 points Most recent by 4ndreas August 2015
• X axis will not home

  270 views 0 comments 0 points Started by jasonsaffle13 July 2015
• Bed will not level in print with dozens of trials

  344 views 6 comments 0 points Most recent by Ulnad July 2015
• RequestPause:Homing failed! message and weird coordinator during Bed Height map

  486 views 5 comments 0 points Most recent by Repetier July 2015
• Delta endstops offset calibration with a stick/rod before doing autolevel G32

  143 views 3 comments 0 points Most recent by Repetier July 2015
• fan OFF g code ?

  1.9K views 1 comment 0 points Most recent by Repetier July 2015
• After 1.5.0 and 1.5.2 always skipping line

  232 views 3 comments 0 points Most recent by Repetier July 2015