Questions & Answers

• modify retract length while printing

  106 views 1 comment 0 points Most recent by Repetier February 2016
• Linear vs quadratic advanced pressure control

  543 views 3 comments 0 points Most recent by Repetier February 2016
• When I set the mixing extruder checkbox should I have multiple extruder sections

  104 views 1 comment 0 points Most recent by Repetier January 2016
• Radds + raps128 Delta optimal advance settings

  516 views 3 comments 0 points Most recent by Repetier January 2016
• Print Quality Test Generator

  98 views 0 comments 0 points Started by Dksre January 2016
• HELP !! Auto-Level, Z Homing, CobbleBot = Total Headache!!!

  413 views 4 comments 0 points Most recent by Repetier January 2016
• Chamber Fan is always active

  205 views 1 comment 0 points Most recent by Repetier January 2016
• 2 Endstops on one axis

  86 views 4 comments 0 points Most recent by Alwin December 2015
• Interupt G code

  77 views 1 comment 0 points Most recent by Repetier December 2015
• Cross post from discussion - Z Probe and first layer problems

  264 views 6 comments 0 points Most recent by Repetier December 2015
• Gcode to control filament motor (E)

  234 views 5 comments 0 points Most recent by Miken December 2015
• Why do servo need another 5V?

  162 views 4 comments 0 points Most recent by sonnylowe December 2015
• Switching from Marlin to Repetier

  347 views 2 comments 0 points Most recent by sonnylowe December 2015
• Proper Way to store/read EEPROM value

  263 views 7 comments 0 points Most recent by Repetier December 2015
• Pause Button

  254 views 2 comments 0 points Most recent by Repetier November 2015
• Install

  77 views 1 comment 0 points Most recent by Repetier November 2015
• Calibration/Bed Leveling

  193 views 1 comment 0 points Most recent by mars0120 November 2015
• Homing backoff for Z?

  184 views 3 comments 0 points Most recent by Repetier November 2015
• E3D PT100 with Amplifier board

  705 views 8 comments 0 points Most recent by Repetier November 2015
• Heater Decoupled - Continue?

  1.5K views 6 comments 0 points Most recent by hopkir November 2015
• Fan Speed, New Version 0.92.6

  171 views 3 comments 0 points Most recent by Repetier November 2015
• It's possible to move after homing?

  204 views 1 comment 0 points Most recent by rfcaldas November 2015
• Setting Acceleration on the fly

  273 views 1 comment 0 points Most recent by Repetier November 2015
• printrbot simple netal config files

  119 views 3 comments 0 points Most recent by Repetier October 2015
• Axis Drift

  140 views 6 comments 0 points Most recent by JMK October 2015
• 5V Fan instead of 12V

  161 views 3 comments 0 points Most recent by Repetier September 2015
• Dual extruder.

  526 views 3 comments 0 points Most recent by Repetier September 2015
• Davinci AIO recent Repetier flash

  482 views 1 comment 0 points Most recent by Repetier September 2015
• http://www.repetier.com/firmware/v092/ - better descriptions for z-probe

  406 views 5 comments 0 points Most recent by Repetier September 2015
• feed rate limited

  638 views 2 comments 0 points Most recent by furynick September 2015