Questions & Answers

• Help Request - AutoBed leveling

  83 views 4 comments 0 points Most recent by Repetier December 2016
• Z-Probe Servo doesn't move for Homing

  167 views 7 comments 0 points Most recent by ex-egll December 2016
• SD Card Removed Message When Starting Print

  53 views 5 comments 0 points Most recent by Repetier December 2016
• M260 (send i2c) available?

  37 views 1 comment 0 points Most recent by Repetier December 2016
• E3D BigBox

  448 views 34 comments 0 points Most recent by Repetier December 2016
• wie muss ich die Offsets in der firmware 0.92 einstellen ?

  156 views 5 comments 0 points Most recent by Repetier November 2016
• Do I always have to change EEprom bit #1 number to save config when I upload ?

  54 views 1 comment 0 points Most recent by Repetier November 2016
• pre-sets for the config tool

  50 views 1 comment 0 points Most recent by Repetier November 2016
• Gcode M104

  93 views 6 comments 0 points Most recent by Repetier November 2016
• newbee trying out the firmware on a (geeetech) g2s pro, and i got some problems.

  146 views 4 comments 0 points Most recent by Repetier November 2016
• Why Repetier only lets me manually move the motors one way? HELP ME PLEASE!

  36 views 1 comment 0 points Most recent by Repetier November 2016
• No Z_PROBE_GAP in firmware

  69 views 6 comments 0 points Most recent by Repetier November 2016
• Soft & hard endstop modification

  32 views 2 comments 0 points Most recent by wangsamax November 2016
• EEPROM new parameter problem

  81 views 4 comments 0 points Most recent by wangsamax November 2016
• Configuring Discount SmartLCD Controller

  57 views 3 comments 0 points Most recent by Repetier November 2016
• auto level mirrored

  67 views 1 comment 0 points Most recent by Repetier November 2016
• How to clear EEPROM 1 or EEPROM2 to defaults from configuration.h ?

  918 views 10 comments 0 points Most recent by N37 November 2016
• Pullups on endstop pins

  110 views 3 comments 0 points Most recent by Repetier November 2016
• [Q] Level delta without computer

  70 views 3 comments 0 points Most recent by Repetier October 2016
• Why whenever I turn on the Printer I only can move the Z axis is one direction?

  77 views 2 comments 0 points Most recent by malebuffy October 2016
• Axis correction

  116 views 6 comments 0 points Most recent by Repetier October 2016
• Dual X axis Help

  114 views 1 comment 0 points Most recent by Repetier October 2016
• Distortion Calibration (Delta)

  70 views 2 comments 0 points Most recent by PhamNguyen October 2016
• Core X/Y Dual Z Options Not Have Config Tools (Due + RADDS)

  71 views 1 comment 0 points Most recent by Repetier October 2016
• 3d Laser Printer

  83 views 3 comments 0 points Most recent by Repetier October 2016
• what is the Gcode to run 2 extruder motors in the same time?

  168 views 6 comments 0 points Most recent by danikurnianto September 2016
• Z-probe on delta printer problems

  117 views 1 comment 0 points Most recent by Repetier September 2016
• Z-Probe on Delta (Hexagon V2) wrong Z-High after Probing

  94 views 7 comments 0 points Most recent by Repetier September 2016
• Probing points problem

  52 views 1 comment 0 points Most recent by Repetier September 2016
• Another trouble with wrong height of Z=0 after Z-Probing.

  78 views 1 comment 0 points Most recent by Repetier September 2016