Questions & Answers

• BL Touch probing

  299 views 8 comments 0 points Most recent by Repetier February 2017
• Sparse first layer - it is necessary to increase the flow of plastic to 135%

  96 views 1 comment 0 points Most recent by MartinH February 2017
• FEATURE_RETRACTION & AUTORETRACT_ENABLED

  641 views 5 comments 0 points Most recent by Repetier February 2017
• Motorized correction

  29 views 0 comments 0 points Started by lotes February 2017
• Need some help.

  40 views 2 comments 0 points Most recent by Sheldouille February 2017
• M665 and M666 unknown command

  269 views 2 comments 0 points Most recent by Repetier February 2017
• Turn fan on/off automatically at temperature?

  140 views 5 comments 0 points Most recent by Repetier February 2017
• How to Home all the axis on boot / startup?

  74 views 2 comments 0 points Most recent by Tech3D February 2017
• Sending GCode through serial

  282 views 3 comments 0 points Most recent by Repetier February 2017
• Homing past Z0

  50 views 3 comments 0 points Most recent by BeastPrinter February 2017
• Dual Z endstops/probing in DEV version

  56 views 3 comments 0 points Most recent by BeastPrinter February 2017
• HAL I2C Routines

  34 views 2 comments 0 points Most recent by RAyWB January 2017
• Feature for stationary endstops ?

  35 views 1 comment 0 points Most recent by Repetier January 2017
• Line No 3 allways missing

  33 views 4 comments 0 points Most recent by Repetier January 2017
• DEV version dragging probe during bed leveling

  39 views 2 comments 0 points Most recent by BeastPrinter January 2017
• Original Config.h File

  108 views 4 comments 0 points Most recent by Repetier January 2017
• G-code for set Z=0?

  83 views 3 comments 0 points Most recent by Repetier January 2017
• Adding new EEPROM definition problem

  35 views 1 comment 0 points Most recent by wangsamax January 2017
• Delta printer and backlash compensation

  56 views 3 comments 0 points Most recent by Repetier January 2017
• Z probing servo scripts work with Z probe but not with Z homing

  75 views 3 comments 0 points Most recent by Repetier January 2017
• POWER ON Anschluss

  49 views 2 comments 0 points Most recent by TomD January 2017
• Query about Z-probe height difference with G28 G32

  46 views 2 comments 0 points Most recent by MartinH January 2017
• M48: Measure Z-Probe repeatability (marlin)

  141 views 3 comments 0 points Most recent by Repetier January 2017
• What option does not allow manual preheating in the repatier firmware?

  126 views 11 comments 0 points Most recent by Repetier January 2017
• The laser turns on and flashes at the beginning of each movement and then stays off until the end.

  43 views 3 comments 0 points Most recent by gilsilex January 2017
• Buffered commands

  76 views 7 comments 0 points Most recent by Repetier January 2017
• Waening: Missed Line Detected – correcting buffer usage.

  117 views 1 comment 0 points Most recent by Repetier December 2016
• Auto bed level "working", software compensation not so much...

  110 views 3 comments 0 points Most recent by nishanth December 2016
• SD Card Error? - Da Vinci 1.0

  70 views 2 comments 0 points Most recent by Repetier December 2016
• autolevel setup help

  265 views 10 comments 0 points Most recent by wizzle111 December 2016