Questions & Answers

• Two controlable fans under RAMPS 1.4

  14.6K views 12 comments 0 points Most recent by neveroddoreven May 2016
• LCD Set to Origin

  140 views 2 comments 0 points Most recent by Cyber_One May 2016
• How to set a LASER PULSE

  666 views 16 comments 0 points Most recent by robgs May 2016
• no printing

  92 views 3 comments 0 points Most recent by eshchari April 2016
• Core xy - Capacitive Sensor for Autoleveling and Home z issue

  247 views 1 comment 0 points Most recent by Blamer April 2016
• right extruder overdrive on Da Vinci 2.0A

  67 views 1 comment 0 points Most recent by weirdguy April 2016
• V92.9 ‘inline’compile error

  74 views 2 comments 0 points Most recent by huanxiang900 April 2016
• Error compiling Repetier-Firmware 0.92.7 (twi.c)

  3.1K views 7 comments 0 points Most recent by Repetier April 2016
• won't compile - 'THERMOCOUPLE_1_PIN' was not declared in this scope

  333 views 4 comments 0 points Most recent by quixotic120 April 2016
• UIMENU and I2C respectively SPI

  247 views 23 comments 0 points Most recent by Repetier April 2016
• Line number missing (*sigh*)

  256 views 3 comments 0 points Most recent by Repetier April 2016
• Can I get extruder temp on another arduino?

  103 views 4 comments 0 points Most recent by Repetier April 2016
• extruder heater decoupling da vinci 2,0a

  51 views 0 comments 0 points Started by weirdguy April 2016
• Extruders swapped

  146 views 7 comments 0 points Most recent by weirdguy April 2016
• how Do i know that Melzi V2 board has a bootloader OR it is Blank ?

  115 views 0 comments 0 points Started by mahmmoud March 2016
• need help

  59 views 0 comments 0 points Started by elniii March 2016
• Gcode to lower bed?

  289 views 2 comments 0 points Most recent by weirdguy March 2016
• Can I disable decouple test in 0.92.8

  102 views 1 comment 0 points Most recent by Repetier March 2016
• Laser and CNC Mill Offset

  258 views 5 comments 0 points Most recent by Repetier March 2016
• Prints are too big on x and y - Repetier 0.92.8

  202 views 2 comments 0 points Most recent by evbohrer March 2016
• Calibration using experimental G100 in 0.92.5 dev

  321 views 3 comments 0 points Most recent by MrBaz March 2016
• New to Repetier setting up RADDS+DUE+RAPS128

  1.8K views 25 comments 0 points Most recent by ldanut March 2016
• Extruder heating nonstop when printer is connected to power supply

  121 views 1 comment 0 points Most recent by Repetier March 2016
• Decoupling error

  843 views 4 comments 0 points Most recent by Repetier March 2016
• Unknown Command Issues

  361 views 4 comments 0 points Most recent by nortybynature February 2016
• Filament Odometer

  163 views 5 comments 0 points Most recent by Repetier February 2016
• Program too big for ATmega1284P

  143 views 3 comments 0 points Most recent by covert February 2016
• Printer Hangs and Restarts after Z Probing

  130 views 3 comments 0 points Most recent by NorcoT February 2016
• Compile problems

  245 views 1 comment 0 points Most recent by Repetier February 2016
• Retraction

  396 views 5 comments 0 points Most recent by kharar February 2016