Motherboard

• Motor cracks when connecting

  1 view 3 comments 0 points Most recent by Repetier May 2018
• Pin assignment changes

  1 view 1 comment 0 points Most recent by Repetier April 2018
• Pin of the second extruder is in place of the fan

  1 view 1 comment 0 points Most recent by Repetier April 2018
• Repetier for K8200

  842 views 17 comments 0 points Most recent by joule5 March 2018
• Smart RAMPS + Arduino DUE: SD card as EEPROM

  1 view 2 comments 0 points Most recent by luxarts March 2018
• RAMPS PLUS 2 motherboard configuration

  1 view 3 comments 0 points Most recent by Anidal February 2018
• Weired display with Megatronics V3.1

  1 view 3 comments 0 points Most recent by Repetier February 2018
• How to configure extension board steppers on RADDS

  1 view 4 comments 0 points Most recent by Repetier February 2018
• MPX.3

  1 view 1 comment 0 points Most recent by MartinH February 2018
• bigtreetech kfb2.0 configuration

  29 views 1 comment 0 points Most recent by denizhanyucel February 2018
• Communication error

  1 view 12 comments 0 points Most recent by Repetier January 2018
• Hotbed Mosfet configuration.h code

  1 view 4 comments 0 points Most recent by Repetier January 2018
• MKS GEN v1.4 temperature fault

  132 views 12 comments 0 points Most recent by Hmark January 2018
• Eeprom on ultratronics pro v1

  1 view 1 comment 0 points Most recent by Repetier January 2018
• Ultratronics pro firmware.

  115 views 2 comments 0 points Most recent by Sebastian January 2018
• Is somewhere a renewable list of repetier (firmware) supported motherboards available? (-)

  1 view 2 comments 0 points Most recent by good_idea January 2018
• Prusa I3 different MELZI motherboards and compatibility

  1 view 1 comment 0 points Most recent by Repetier December 2017
• Using Melzi's expansion header to fix heated bed temp circuit.

  1 view 5 comments 0 points Most recent by Repetier December 2017
• MKS v1.4 with TFT 2.8 and bltouch. Need help plz

  1 view 4 comments 0 points Most recent by Repetier December 2017
• MKS Sbase v1.3 + Repetier Firmware

  1 view 2 comments 0 points Most recent by JSNU November 2017
• RADDS v 1.5 for IDEX printer

  25 views 3 comments 0 points Most recent by Repetier November 2017
• Repetier FW + Ramps 1.4 + Xbox360 power supply

  38 views 1 comment 0 points Most recent by Repetier October 2017
• Firmware config for Megatronics 3.1

  23 views 1 comment 0 points Most recent by Repetier October 2017
• which motherboards support 3 extruders

  61 views 2 comments 0 points Most recent by recoush September 2017
• Best supported ARM based controller.

  66 views 2 comments 0 points Most recent by Twmaster September 2017
• Extruder polyfuse getting very hot and stopping print

  108 views 21 comments 0 points Most recent by RAyWB August 2017
• MeCreator 2 with GT2560 rev B port to repetier

  253 views 4 comments 0 points Most recent by wiccan2 August 2017
• How to find and update firmware for MPX.3

  77 views 5 comments 0 points Most recent by RAyWB June 2017
• Multiple mcu-s

  59 views 3 comments 0 points Most recent by RAyWB June 2017
• How to enable x,y,z max endstop?

  195 views 1 comment 0 points Most recent by Repetier May 2017