Jerome
About
- Username
- Jerome
- Joined
- Visits
- 35
- Last Active
- Roles
- Member
Comments
-
So fat32 does not work? Ill try thanks.
-
Hi, Can you telle me how you did it> what file dit you edit and what was the change? thanks
-
ok, I was afraid of that. That's why I used the ULN2003 which has a output current of 500mA so I can connect 4 TB6600 on one output for my 4 stepper motors on Z-Axis. Thanks for the info
-
That might be an option too. Do you know what the input signal current for the TB6600 is?
-
For the 3.3 -> 5 Volt I already designed the electronics using ULN2003 and a few transistors. ULN2003 because I need a current booster to connect 4 stepper drivers (Z-axis) to one output of the arduino. ASfter I tested with a stepper drive simula…
-
For the 3.3 -> 5 Volt I already designed the electronics using ULN2003 and a few transistors. ULN2003 because I need a current booster to connect 4 stepper drivers (Z-axis) to one output of the arduino. I tested with a stepper drive similar to t…
-
Thank You. Your support is great. I just sent a donation! Keep up the good work
-
Jerome said: Hi, How to connect an external stepper driver like TB6600 to radds/ramps board? Common negative or common positive? Picture shows common positive: http://i.imgur.com/59Ot1iB.png Thanks for your help So in other words are the…
-
Suggestion for the repetier plugin for inkscape. Add the possibility to switch laser on/off with M3 and m5 command instead of the G0/G1 as it is now.
-
Repetier said: Don't do all the reinstalls. It is in firmware or the gcode you send or a combination. My problem is that I'm too busy to test myself at the moment. You could test without M3 and only use increasing E values where you want to…
-
Roko said: Repetier said: Does laser turn off for G1 instead? Then you might have LASER_ON_HIGH wrong also it would be safer that it only turns on with high signal. Also check no other function uses pin 57 to interfere. Like he said, does i…
-
That's right. Today I tried a few things. Replaced my Arduino mega -> no difference Uploaded the latest firmware -> no difference Still first G0 move laser on I am out of ideas ..
-
Hi, Still not working correctly. I checked, no other assigned to pin 57 except #define ANALYZER_CH7 57 // ysig in Repetier.h The code in Commands.ccp is same so no issue there. I tried the following. Two letters, A and B about 5 cm apart from ea…
-
Hi, laser switches on (pin 57 HIGH) with this line: G0 X46.6438 Y-14.1442 In configuration.h #define SUPPORT_LASER 1#define LASER_PIN 57#define LASER_ON_HIGH 1 If I move the head manually using G0 X10 Y10 laser is on also when moving using repe…
-
Repetier said: Make sure the travel moves use G0 not G1. G1 will enable it on the way while G0 keeps laser off until target is reached. How do I do that? In de repetier plugin for inkscape there is no setting for that. This is the beginn…
-
Hi, can I change this in eeprom settings?If yes how and where. What is the difference in eeprom between 'corr diagonal' and 'dealta radius' ? Thanks again
-
That is not exactly what I mean. In repetier there are 'build in' slicers. I like to add simplify3d to that. Is it possible?
-
sorry my setting: Z_PROBE_Z_OFFSET_MODE 0 Custom bed coating maximum is about 2.5 mm I cannot get it higher. Glass plate 3mm so it's not enough.
-
It's working a bit. Maximum is about 2.5mm can I change that? setting:
-
Ok this is working now. Another problem came forward since distortion correction The first few layers seem to be over-extruding now untill they reach about 1.4 mm.After that print is normal again. How can this be corrected? thanks
-
Thanks I will try this
-
Thanks, If I understand well:When the nozzle touches the bed and at the same time the z-probe triggers at 2mm the z-probe height would be 2mm. Do I measure with M114 of fysical height? So this is a fixed value. Max z-probe bed distance is the heigh…