Roko
About
- Username
- Roko
- Joined
- Visits
- 1,389
- Last Active
- Roles
- Member
Comments
-
what was it?
-
I think the decoupling settings and min/max defect temperature are checking for a thermal problem. Along with Kill_if_sensor_defect being enabled.
-
Yep if the drivers are oriented incorrectly they will not work.
-
M119 shows H when endstops activated ? could you post the actual configuration.h that was used to load to the board? (In case something got d/l'd wrong)(just a thought)
-
possibly reduce your steps/mm. I would try about 1/2 of # of steps setting or even lower just to see if they will move.
-
check pin/connector area for blackened pins where motor plugs in. Could be poor connection.
-
I don't know if this "helps", I seem to recall when I had a probe on my Delta I started with all correction turned off, but left the Z-probe enabled. I made sure Z steps were calibrated, then I set my center position on the bed at Z=0 manually and m…
-
I did not think the learning curve is that steep. It does what I need to do, quite well. There are other programs if this does not suit you.
-
You can try this link: http://reprap.org/wiki/Triffid_Hunter's_Calibration_Guide
-
Also they blink when the steppers become disabled after the stepper timeout or if done by user.
-
you could try disabling distortion correction, manually level bed as best you can and see if layers are seperated though the print might not be as good on 1st layer.
-
@Marco67 In the Repetier-Host go to Config - Printer Settings - Printer. You can set a park position. You can set it up to go there after a "Job Kill" , or use the P icon under Manual Control, or it will go there after a job is fi…
-
M851 is a Marlin/MK4Duo firmware code for setting Z-probe offset. You need to look at the above reference
-
Are your probe offsets correct?A suggestion, go to a certain X,Y coordinate and mark the bed (lets say X50, Y50). Then do a g30 to the same coordinates. If your probe x,y is right you will touch in the same spot with the probe. You might be probing …
-
You are welcome Another possibility - run it from an sd card?
-
You could also setup a script using the Z-min. I did it on my CoreXY and it works fine. I don't have a Z- probe on it. Here is my script. It homes, drops Z15, goes to the each point in the back , waiting 10 seconds at each, moving to the other, then…
-
The configuration files (configuration.h and configuration_adv.h), you are looking for are used for the Marlin firmware. Repetier has just configuration.h. That is what I thought you were looking for as a reference to make your own configuration. T…
-
did a quick google search, there is a lot of stuff out there.
-
elidor said: Ok i got somthing disabling DAC didnt help , im still getting the massage and the result of that . (extruder decoupled ) now... when im not using the fan , the printer didnt stop to print all the way . which is good for now …
-
You found it. Good Job! Happy Printing! No shame in learning.
-
The video I looked at: 5:44 into video shows PS connection. 6:25 show board connector plugged in. I don't have that printer but if you don't have the voltage motors/fans won't work. I am pretty sure the green LED should stay on. Try by disconnectin…
-
Repetier said: Open log and see responses. If you can read temperatures from firmware the connection is not your problem. You have either not enabled power or you must send M80 to enable power if using an ATX power source. Hope you got a conf…
-
sure you are not in dry run mode?
-
open a cmd window then type it into the window. If you are not logged in as Administrator it will tell you so and not run. That might be why it ran so fast. (happened to me).
-
rshafersr said: so in order to use the manual control, i would have to load an object and go to print so when the extruder has reached temperature i use the filament advance control to insert new filament and then keep feeding until the color…
-
You are correct about the 200 when it shows initially. If you are using the default profile (under CuraEngine) and the filament temp is set to 200 it SHOULD compile at 200. The start g-code script is under Slicer - CuraEngine - Configuration - Prin…
-
A quick check on the stepper is move your tower connectors over one ( x -y, y-z, z-x)and see if it moves to the new tower.
-
make sure all the jumpers are installed under the driver pcbs. I made these the same number: 2 #define ENDSTOP_X_BACK_MOVE 5 #define ENDSTOP_Y_BACK_MOVE 5 #define ENDSTOP_Z_BACK_MOVE 2 I used 2 here: #define ENDSTOP_X_BACK_ON_HOME 0 #define EN…
-
also you mention error occurred at the same place every time on that object. perhaps you have an intermittent contact at that position (Z-height) and type of movement (infill, etc.) that causes a momentary problem with the connection at that point i…
-
try checking your wiring.