NickRno77

About

Username
NickRno77
Joined
Visits
13
Last Active
Roles
Member

Comments

  • @Repetier Ok that’s an interesting theory but it doesn’t take into account the sometimes very fast movements and the diagonal line across the corners phenomenon. Also this carried on all the way through the print on the photo I sent you …
  • Repetier said: Try activating ping-pong. Than print order is same as in OctoPrint. Otherwise server will try command sin parallel and with bad input buffer size that can cause problems, but these normally get fixed. But would not be the only …
  • Repetier said: In communication settings of printer in server. My ping pong is not set on, If I get problems again  I’ll switch it on.
  • PGe68 said: Hi, I'm been following your advice on activating ping-pong and now it seems to be working fine again. I have tried to print the same Gcode that failed and it looks goodI have no idea what ping-pong really is / does but it look…
  • PGe68 said: I have two MK3S and one MK3S +, I run MK3S on FW 3.9.3 and I run MK3S + with FW 3.10.0-RC1 and all three printers have the same error. I tried last night to reInstall Repetier-Server with Image V25 (1.0.4) on a new RPi 4 4GB, new …
  • PGe68 said: NickRno77 said: Repetier said: You should upgrade to 1.0.4 for all the fixes being made. Not really sure what is going wrong here - looks a bit like under extrusion but for some moves it seems extrusion misses comple…
  • Repetier said: You should upgrade to 1.0.4 for all the fixes being made. Not really sure what is going wrong here - looks a bit like under extrusion but for some moves it seems extrusion misses completely. Maybe not switched to relative extru…
  • NickRno77 said: Every now and then my prints get corrupted, varies but usually I have to reinstall the Pi Deb install to resolve then ok till the next time. It’s not the GCODE because when I use the same GCODE after reinstall all is ok. v0.94…
  • PGe68 said: Hi, I have got exactly the same problem. I have run Repetier for a while now and this problem begins last week for me. I have MK3S+ and have checked my belts, I have clean and re-greased all moving parts, I have run belt check on …
  • Repetier said: Maybe. It uses these values to eliminate stringing: https://cln.sh/gWHWAg Especially retraction distance and retraction speed. These are used in slicer to reduce stringing and can be used for snapshots as well. I only get …
  • Repetier said: 1) In our image that is the shutdown button. It will shut down pi so you can unpower safely. 2) Maybe  @waitForAllTemperatures maxDiffWill wait for all set temperatures to be within the given difference. If maxDiff is omitted, …
  • @Repetier I’m using the latest from Bear Labs FW3.9.3 which is slightly modded from the Prusa MK3S version. https://github.com/bear-lab-3d/Prusa-Firmware/releases
  • Just to let you know, I read in one of the Octoprint forms there was a similar issue to this caused by Marlin FW. Maybe this is the same problem in my case. I added M155 S1 to Run on Connect in Printer Settings>Event Dependent  Seems ok to me l…
  • Repetier said: Does this always happen when you deactivate and activate printer in server? IT just doesn’t happen in graph or temp status anywhere, just get one temp reading when Repetier connects with printer that’s it.  I’ve now run  M15…
  • Could it be something to do with a recent Prusa FW Update? 
  • I enabled ack and disabled M105 filter still no updates. I then ran M115 graph and temp updates started working ? Is this permanent now? 
  • Repetier said: See PM Sent you email.
  • Repetier said: You never know if it is too late. In home screen it is  in the printer menu top left. I've finally worked out where to download the printer.xml how can I get it to you ?
  • Repetier said: That looks bad. No values at all. Haven't seen that on my printers running 1.0.2 so wonder what is causing this. Looks like it fails to read the settings. Can you send me your printer xml config? Need to release new version tom…
  • Repetier said: Is there an error message for the conversion? Does recreating video work or ore the images missing? Is there enough disk space? When disk space gets low timelapse stops taking images. no errors no video no images 50gb free …
  • @Repetier The compiled video from the snapshots can’t be seen under recordings. And the settings aren’t saved when I access the interface via a web browser. Although they are on the Pi Touchscreen. I noticed one occasion the thumbnail o…
  • @Repetier Sorry I should have created a new post. I updated using the Pi Screen auto updater. Just to make sure the deb file for downgrade is Linux 32 bit ARM (armel): libc 2.13 like on Raspberry-Pi Raspian. I also can’t…
  • I have similar issues since updating to V1.02, how can I roll back to 0.94.3 please, ? 0.94.3 was solid for me. I have Prusa Mk3s and Rasberry Pi 3b
  • Repetier said: The rumba einsy would be a mega 2560 compatible board. So if it works then with that setting. I was having trouble flashing the latest Prusa FW so the your FW Uploader saved me a lot of trouble. I new the Prusa had a Einsy B…
  • Repetier said: Have a look at this website it explains how to do it. Different webcams have different possible parameter. https://www.kurokesu.com/main/2016/01/16/manual-usb-camera-settings-in-linux/ Once you have the command to change them …
  • cosmith71 said: I had this same problem.  Try this instead. M115 U3.7.2; tell printer latest fw version G90; use absolute coordinates M83; extrude relative mode M104 S [first_layer_temperature]; set extruder temp M140 S [first_layer_bed_…
  • Repetier said: Normally that is http://ip:8080 or what ever port it was assigned. So just the beginning of the url you entered as webcam url with your ip instead of localhost. I did try that yesterday but didn't work but does now thanks.  …
  • Repetier said: 1) It is defined in printer settings->General->Manual Control. Enter the speed you like there. 2) You can use the mjpg_streamer url manually. It has a web interface allowing to change some values. You can also add the set…
  • cosmith71 said: After 3 days and 1 broken screen, I finally got the HyperPixel working on a Pi 4 with Repetier-Server. It turned out to be a simple fix.Note, I'm using a wired Ethernet connection.Flash Repetier-Server to an SD card. Add an em…