NickRno77
About
- Username
- NickRno77
- Joined
- Visits
- 22
- Last Active
- Roles
- Member
Comments
-
Repetier said: Try ls -l /dev/v4l/by-id/ and use full path to the one that looks correct. I got the auto wrong, when I listed the video settings focus_automatic_continuous showed up not focus_auto=0 that was my problem. I should of checked…
-
@Repetier Logitech C920
-
@Repetier I've finally got a working version of Repetier Server, Logitech c920 is working fine but only problem now I need to turn autofocus off and set a fixed value of 50. Back I the day I managed to fix but now I'm a bit clue less where I ne…
-
spinxinfotech said: Repetier Server is compatible with the Hyperpixel 4 touchscreen; however, for the touchscreen to work properly, make sure the appropriate drivers are installed on your Raspberry Pi. For best results, you will also need to …
-
NickRno77 said: Repetier said: It changes x display configuration when you save so boot/config settings should have no effect. But when rebooting undoes it I would say it did not save. Maybe run in ssh terminal the commands manually s…
-
Repetier said: It changes x display configuration when you save so boot/config settings should have no effect. But when rebooting undoes it I would say it did not save. Maybe run in ssh terminal the commands manually so you can see responses…
-
Repetier said: Should detect pi so no extra license will be used, otherwise go to registration and hit deactivate first and activate on next install. If you loose some licenses due to defect sd cards write to our support with license code. …
-
@Repetier i did go through the config tool but didn’t see anything on the HyperPixel display, possibly the screen saver had kicked in. I’ll have another look. How can I get my pro license back please. Thanks
-
Hi, I've just rebuilt the Repetier Server, not sure what happened to make me rebuild it just couldn't communicate. I've installed the latest build of Repetier Server Bookworm version. I couldn't get anything out of the screen till I followed http…
-
@Repetier Ok that’s an interesting theory but it doesn’t take into account the sometimes very fast movements and the diagonal line across the corners phenomenon. Also this carried on all the way through the print on the photo I sent you …
-
Repetier said: Try activating ping-pong. Than print order is same as in OctoPrint. Otherwise server will try command sin parallel and with bad input buffer size that can cause problems, but these normally get fixed. But would not be the only …
-
Repetier said: In communication settings of printer in server. My ping pong is not set on, If I get problems again I’ll switch it on.
-
PGe68 said: Hi, I'm been following your advice on activating ping-pong and now it seems to be working fine again. I have tried to print the same Gcode that failed and it looks goodI have no idea what ping-pong really is / does but it look…
-
PGe68 said: I have two MK3S and one MK3S +, I run MK3S on FW 3.9.3 and I run MK3S + with FW 3.10.0-RC1 and all three printers have the same error. I tried last night to reInstall Repetier-Server with Image V25 (1.0.4) on a new RPi 4 4GB, new …
-
PGe68 said: NickRno77 said: Repetier said: You should upgrade to 1.0.4 for all the fixes being made. Not really sure what is going wrong here - looks a bit like under extrusion but for some moves it seems extrusion misses comple…
-
Repetier said: You should upgrade to 1.0.4 for all the fixes being made. Not really sure what is going wrong here - looks a bit like under extrusion but for some moves it seems extrusion misses completely. Maybe not switched to relative extru…
-
NickRno77 said: Every now and then my prints get corrupted, varies but usually I have to reinstall the Pi Deb install to resolve then ok till the next time. It’s not the GCODE because when I use the same GCODE after reinstall all is ok. v0.94…
-
PGe68 said: Hi, I have got exactly the same problem. I have run Repetier for a while now and this problem begins last week for me. I have MK3S+ and have checked my belts, I have clean and re-greased all moving parts, I have run belt check on …
-
Repetier said: Maybe. It uses these values to eliminate stringing: https://cln.sh/gWHWAg Especially retraction distance and retraction speed. These are used in slicer to reduce stringing and can be used for snapshots as well. I only get …
-
Repetier said: 1) In our image that is the shutdown button. It will shut down pi so you can unpower safely. 2) Maybe @waitForAllTemperatures maxDiffWill wait for all set temperatures to be within the given difference. If maxDiff is omitted, …
-
@Repetier I’m using the latest from Bear Labs FW3.9.3 which is slightly modded from the Prusa MK3S version. https://github.com/bear-lab-3d/Prusa-Firmware/releases
-
Just to let you know, I read in one of the Octoprint forms there was a similar issue to this caused by Marlin FW. Maybe this is the same problem in my case. I added M155 S1 to Run on Connect in Printer Settings>Event Dependent Seems ok to me l…
-
Repetier said: Does this always happen when you deactivate and activate printer in server? IT just doesn’t happen in graph or temp status anywhere, just get one temp reading when Repetier connects with printer that’s it. I’ve now run M15…
-
Could it be something to do with a recent Prusa FW Update?
-
I enabled ack and disabled M105 filter still no updates. I then ran M115 graph and temp updates started working ? Is this permanent now?
-
Repetier said: See PM Sent you email.
-
Repetier said: You never know if it is too late. In home screen it is in the printer menu top left. I've finally worked out where to download the printer.xml how can I get it to you ?
-
Repetier said: That looks bad. No values at all. Haven't seen that on my printers running 1.0.2 so wonder what is causing this. Looks like it fails to read the settings. Can you send me your printer xml config? Need to release new version tom…
-
Repetier said: Is there an error message for the conversion? Does recreating video work or ore the images missing? Is there enough disk space? When disk space gets low timelapse stops taking images. no errors no video no images 50gb free …
-
@Repetier The compiled video from the snapshots can’t be seen under recordings. And the settings aren’t saved when I access the interface via a web browser. Although they are on the Pi Touchscreen. I noticed one occasion the thumbnail o…