umtauscher
About
- Username
- umtauscher
- Joined
- Visits
- 13
- Last Active
- Roles
- Member
Comments
-
That finally did the trick.I really appreciate your patience.Thanks
-
Ok, just tested: /usr/local/Repetier-Setup/bin/startAllCams doesn't change anything.I still have to go in the frontends setup and click "restart webcam server" to get it working.So the webfrontend must do something different.
-
I'm sorry, but that does not work.I still have to restart the webcam server to get the stream working
-
Thanks, but I really don#t know what I am looking for. The output of the dmesg command ends with: [ 13.034450] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 13.634543] usb 1-1.2: reset high-speed USB device number 3 using xhci_hcd [ …
-
Well, it kinda seems to work, but the autostart file is in/home/pi/.config/openbox/
-
Thanks, I‘ll try that
-
Well, thanks, that is very inconvenient. I think I stick with the old image and try to fix it.
-
Just to make sure, I have just reinserted the old SD-card and the touchscreen ist just working fine again.
-
I'm sorry, you lost me...
-
Thanks for answering, but maybe I didn‘t explain properly what I was thinking: Repetier implements 3 Buttons in Homeassistant: Pause, Continue, Stop that are implemented via the HA autodiscovery via MQTT. What I was thinking about is an additional …
-
@Repetier If I understand corrctly, you don't want do implement this?How would I implement an action that Repetier executes on a specific MQTT Topic/Message?
-
@Sonicboom Actually no, that would not change anything in fact. I have no problem switching off the printer via a smart plug. I don't need Repetierserver for that.We are talking about Homassistant , right? What I would like to do is to have the a…
-
Thanks, that was it.Cheers
-
hmm.The Pi/Repetier behaves as if it were running in an ramdisk.Alle printjobs or timelapse files that I delete are also magically back after a reboot.I'm no Linux specialist, I'm at a loss. Any Ideas?
-
... and another idea:It would be nice, if Repetier would send a last message to MQTT before shutting down with anything that would represent the downstate. Other MQTT devices for example have a status field that show online or offline.
-
ok, that shuts down the printer after a M117 command. My intention ist to safely shutdown Repetier Server (Rapberry) before switching off the power. I my installation the Repetier Server is powered by the same circuit that powers the printers.
-
@Sonicboom You can turn off your printer using you plug and defining an automation that reakts on the printers states. @RepetierIt would be a great feature, if we could shutdown the Repetier Server via a button like the pause,stop,continue buttons.…
-
Ok, sorry I just found updated to version 1.41Everthing seems to be working perfectly.Thanks
-
Thanks for that integration. Unfortunately there seem to remain 2 problems :When trying to get the job_start and job_end sensor. the integration fails with this error message.It would be very nice, if you could do something about it.Thanks in advan…
-
Danke, leider waren die Temp-Offsets auf 0 Ich werde versuchen das Log zu prüfen.
-
Ich benutze den Prusaslicer mit der Direktdruckfunktion. Dabei habe ich allerdings das problem, dass von Zeit zu Zeit bei Druckstart die Betttemperatur auf 70-90° gestellt wird. Wenn ich mir die gcode Datei ansehe kann ich keine Grund dafür erkennen…
-
Great, I knew it! Thanks
-
So complicated? I thought since there is already a shutdown server command in der Raspis Touch UI it should be a bit more straight forward.
-
So I managed to enter a web action to switch off the printer. This one is aktivated by an event driven gcode ;@webAction PrinterOff What I would add now is a gcode to shutdown the raspi with repetier server itsself. How can I do that? I can‘t find …
-
Thanks, I will try…
-
Sorry, its 1.2.1
-
Danke für Deine Geduld. Ich war etwas begriffsstutzig, sorry.
-
Das ist ja schön, nur wie soll mir das weiter helfen? lsusb Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 005: ID 046d:0823 Logitech, Inc. HD Webcam B910 Bus 001 Device 007: ID 1a86:7523 QinHeng Electronics HL-340…
-
In by-path stehen nur die beiden Kameras. Wäre auch eine gewagte Theorie und würde eigentlich bedeuteten, dass man kann keine 2 identischen Drucker anschließen könnte, wenn man sie unterscheiden will.
-
danke schonmal für die Antwort. Mit dem syslog kann ich aber nichts anfangen.USB0 ist der Drucker, den ich gerade angeschlossen habe: ls /dev/serial/by-id hat keine neuen Eintrag: (Die Raspi Installtion ist übrigens da 1.04 Image auf Raspberry 4) Ju…