Repetier_Support
About
- Username
- Repetier_Support
- Joined
- Visits
- 24
- Last Active
- Roles
- Member, Moderator
Comments
-
can you try to ping the following domain? https://licence.internetloesungen.com
-
Hello! A Raspberry Pi (3+) is normally powerful enough to control all 10+ printers. The big bottleneck would be the usb bandwidth. Thats why we would recommend you a moderate PC with, as you said, additional PCIe USB Cards. Also we highly recommend …
-
Hallo. Dieses Problem haben wir bereits in der Version 1.1.0 behoben, welche bereits auch veröffentlicht ist.
-
Hallo, Ich vermute der mjpg-streamer ist abgestürzt. Du kannst ihn ihn neustarten, wenn du in die Druckereinstellungen unter Webcam gehst und dann auf "Restart Webcam-Server" klickst. Danach sollte die Webcam wieder sichtbar sein
-
If the firmware requires a uppercase syntax and the commands contains lowercase letters, the commands are invalid. It doesn't make sente to put everything in uppercase, because some firmwares or the server itself do use case sensitive commands, whi…
-
Hello. We could reproduce this issue and it will be fixed within the next update.
-
This touchscreen interface is supposed to only work over localhost. The only way you could connect to this interface is setting up a proxy on your windows machine.
-
Hello. Yes you are right, the settings in Repetier-Host are for the control and display functionality and won't be used for slicing.
-
Hallo. Ein Semikolon (;) ist normalerweise ein Zeichen um einen Kommentar zu kennzeichnen und werden somit nicht an Drucker gesendet. Um die Befehle trotzdem verwenden zu können kannst du vor dem Semikolon ein # machen. (#;C2560_RES). Somit wird d…
-
Which operating system do you use?
-
In the webinterface under Printer->Control you can switch between the extruders on the right side under temperatures. To see both extruder temeratures at the same time, click on the temperature icon under Printer -> Control
-
What is the result of vcgencmd get_camera ? Should be:supported=1 detected=1 Are you using our image or the original raspbian image? Only our version is supposed to show the webcams.
-
Du kannst einen neuen Drucker ganz einfach hinzufügen über den Plus-Knopf oben rechts im Dashboard. Falls es Probleme gibt, das der Server einen Drucker falsch zuordnet, siehe hier: https://forum.repetier.com/discussion/8948/problem-mit-2-druckern-a…
-
Connect to a terminal session of your RPi, put the deb file on the filesystem and install it with sudo dpkg -i Repetier-Server-1.0.5-Linux.deb Usually you should use armhf for RPi 3 and above. To check witch version of build your installation suppo…
-
Du musst beim Geräte-Port nach dem Port, der mit /dev/serial/by-path beginnt suchen. Von da an ist es wichtig den Drucker immer mit dem gleichen USB Port zu verbinden.
-
Hallo. Du könntest dir den Repetier Server Monitor installieren. In diesem kannst du einstellen, dass das Programm eine Ordnerstuktur anlegt, die dann überwacht wird. Je nachdem wo du dann die GCode-Datei einordnest wird der Server entweder den G…
-
Das Problem mit dem Übersetzungsplugin wird im nächsten Update behoben sein.
-
Did you configure your temperature settings correctly?
-
You can already store your Gcodes in projects and be able to download all files at once. You will get those files packed in a zip archive with their renderings.
-
Eine weitere Möglichkeit für deinen Fehler könnte ein falsch eingetragener bzw. beschädigter Bett-Thermistor sein. Dies könntest du eventuell überprüfen. ---- Um die Sicherheitsroutine des Betts an zu schalten musst du in Configuration.h THERMAL_…
-
Du kannst das Logging anschalten, indem du oben rechts bei den Parametereinstellungen auf Druck Logs gehst und dann "Logge Kommunikation beim Drucken" anhakst. Nachdem du dann was gedruckt hast kannst du das Log auf der gleichen Seite unten sehen un…