Morningside
About
- Username
- Morningside
- Joined
- Visits
- 19
- Last Active
- Roles
- Member
Comments
-
Hmmm. Maybe I was just not waiting long enough for it to communicate? It seems to be working now. But I was adding it just as you've recommended to begin with. I think it was just good old fashioned user error it would appear. Thank you!
-
Repetier said: Ok echt komisch was chromium da macht. Hab es jetzt mehrfach getestet und ergebnis war immer mal anders. Hab autostart jetzt auf folgenden Inhalt geändert, der jetzt stabil zu funktionieren scheint: # Uncomment the following 3…
-
It also appears that rebooting the server from my desktop gets it back to normal. But switching it on from the power cord goes back to incognito mode, and I'll have to reboot it again to get it back. I'm sure this happened after a "apt dist-upgrade"…
-
Repetier said: Ok echt komisch was chromium da macht. Hab es jetzt mehrfach getestet und ergebnis war immer mal anders. Hab autostart jetzt auf folgenden Inhalt geändert, der jetzt stabil zu funktionieren scheint: # Uncomment the following 3…
-
What about on a pi? I'm having the same issue, and the above command does not work. No such file or directory.
-
Disk is not full, but I can try another one just to check. Pi is always shutdown by shutting down the server first either in the touchscreen, or via browser, then the pi is shut down. Last undervoltage and cpu throttle = never. Below is a secti…
-
Disk is not full, but I can try another one just to check. Pi is always shutdown by shutting down the server first either in the touchscreen, or via browser, then the pi is shut down. Last undervoltage and cpu throttle = never. Below is a sectio…
-
Sonicboom said: this makes no sense to me, why would you need to reach the server locally if you are in your house or shop? i am trying to reach the server externally and it just does not work, have external IP:2000 nat'd to local server …
-
Yeah, I just began looking into that. Gonna play around with it. Thanks!
-
This one seems to have been a slicer setting my e steps for some reason. They were set to 415 and I came up with something around 144 when doing another calibration. Don't know how it got set to that in the firmware, but it's fixed now.
-
Repetier said: So if local also does not work, what does this solution mean: > So I'm just using a hostname with repetier, and so far I've had no problems connecting. I can live with that! and what ip does it then get. Actually I'm a bit …
-
Repetier said: I wonder which ip then the working .local address has? It uses dhcp after all. Only thing I can think of is that it gets a ipv6 ip instead. Both is active on our image. You could try ping at the local address to see the ip that…
-
The asus router does it pretty easily. When I view a list of connected devices, if I choose one, and change the ip, then it binds the ip address to that device. I can also do it in the lan settings, under the dhcp server. As stated, I have 4 other i…
-
So, I went ahead and started from scratch. I downloaded the image, reflashed, and setup over again. Everything worked, except when I assigned the server a static ip via my router. That's when things went south. This seems to be the issue, although I…
-
Repetier said: When the wifi configuration over repetier-server is not working (which actually just generates a wpa_supplicant file until wifi is not connected any more), you can disable this and do it manually so server can not interfere. Ju…
-
Correction: I can't even use this thing. Will not connect. When it does, it immediately goes away. But I'm using my octoprint pi on wifi no problems. This is what leads me to believe it's in the repetier server, and not my router configuration or ot…
-
Repetier said: Best is to tell dhcp server on your router to always assign same ip address. Much easier then assigning a valid static ip and mask and gateway that does not get used by dhcp as well. The hostname.local also should work if it i…
-
Should I not use a static ip and just try the hostname?
-
The 5v pins have been covered since before this happened. As for lights, I'm not using any. I checked the log, but I must have cleared it because it only has todays dates in it so I'll have to wait until it does it again I guess to take a look there…
-
It's an Asus RT-AC86U. And so today I woke up to 2 prints still going, one finished, and can't reach the server via my phone on the same network. Again, about 5 minutes later, it loaded. Now I'm waiting for it to be reachable from my desktop. But I …
-
It's connected via wifi. As I mentioned, it's connected. But not reachable. Says connected on the touchscreen, and in the routers configuration. But it will not load. I didn't mention before, but I did try turning off the AP mode. That didn't help. …
-
Now I forgot to mention, it seems to come back after about 10 minutes of waiting?? For example, when I posted this, it was unreachable. Now I hit reload again (for like the 18th time), and it's there. I don't understand this. And also, I have tried …
-
Ok, so the part of the knowledgebase article about using a usb hub instead went right over my head. I just plugged in my hub, and plugged the printer into that, and this time it appears to be working.
-
Not sure of the actual brand name. Possibly Lebula? It's a 7" and worked out of the box without installing drivers. And as mentioned, continues to work as long as my printer isn't plugged into the pi.
-
Ok, I did tape up the 5v power pin on the usb cable, but still getting the same result. If the printer is plugged into the pi when it boots, touch will not work. I've looked at that log, but I don't really know what to look for to know. What should…
-
Thank you. Will try all this today. I believe your suggestions may lead to a solution! I will report back later tonight! I do have an appropriate power supply but I believe the printer trying to draw power from the port is the problem now.
-
So yesterday, I reflashed, started over, and again, it seemed to be working. Today I start it up, and again, no touch. I disconnect the printer USB cable, and then it works again. What could cause this? I believe this to be the issue. Something in t…