Buttons

Comments

• Seems to be very useful. I second this!

  in Optionally show retractions in 3d preview (and Manual Control) Comment by Buttons June 2018
• Zu einfach. Besten Dank!

  in Handling von Endstops Comment by Buttons May 2018
• Mhh, ist es denn möglich den zweiten Homing-Vorgang zu unterbinden?

  in Handling von Endstops Comment by Buttons May 2018
• Works great so far. I couldn't discover drops in quality, but speeds are much better now.

  in CoreXY and Quad Stepping? Comment by Buttons May 2018
• Genau das ist gemeint. Ich dachte nur, vielleicht wäre es für eine bessere Übersicht eine gute Idee die Anzeige des aktuell gedruckten Layers in die Druckstatistiken zu verfrachten?

  in Aktueller Layer in den Druckstatistiken Comment by Buttons May 2018
• Great answer. Now I understand what it really does. Thanks!

  in CoreXY and Quad Stepping? Comment by Buttons May 2018
• I second this idea!

  in Historial temperature data Comment by Buttons May 2018
• Thanks for explanation.

  in What are low PID values? Comment by Buttons May 2018
• Do you have an idea when 2.0 will be released to the public?

  in Repetier Host: Manual control for 2nd fan Comment by Buttons May 2018
• Another question: Cooler PWM speed / EXT0_EXTRUDER_COOLER_SPEED is the setting for controlling the speed of the extruder cooler, isn't it? My problem is the fan runs with max speed though I set the PWM to 128 (half speed).

  in Hotend cooling fan not turning on when heating extruder Comment by Buttons May 2018
• Perfekt, danke.

  in Z-Homing einstellen Comment by Buttons May 2018
• Thank you. Yes, I confused the second cooling fan with the extruder cooling fan. Maybe you want to rename the entries in the FW configurator? I think it's a bit misleading. Maybe you want to rename to Fan pin for first print cooling fan Fan pin f…

  in Hotend cooling fan not turning on when heating extruder Comment by Buttons May 2018
• Thanks!

  in Repetier Host: Manual control for 2nd fan Comment by Buttons May 2018
• Thank you!

  in Setting PID values without using the EEPROM? Comment by Buttons April 2018
• Do I understand this correctly: Do I have to switch the FW to Delta, then back to CoreXY?

  in CoreXY and steps/mm Comment by Buttons April 2018
• Thanks a lot. I will try that.

  in CoreXY and steps/mm Comment by Buttons April 2018
• Mhh I can't find this option in the Firmware Configuration Tool. Where is and what does it do when enabled or disabled? I guess when it's not in the config tool then it count's as disabled?

  in CoreXY and steps/mm Comment by Buttons April 2018
• It was the drivers. All dead-on-arrival. No joke. I couldn't believe the whole batch that I ordered was broken.

  in All motors energized but not moving at all Comment by Buttons April 2018
• Ok, problem's finaly solved. Thread can be closed now.

  in All motors energized but not moving at all Comment by Buttons April 2018
• @Roko: Yes, M119 returns a "H" when an endstop is activated. The endstops seem to work flawlessly. The configuration.h of the current version of my firmware can be found here: https://justpaste.it/1jbq6 @MartinH: Sure, but I'm afraid that doesn't …

  in All motors energized but not moving at all Comment by Buttons April 2018
• Roko, thanks for your answer. Unfortunately, no luck with lowering the steps/mm. I set them to 200 steps/mm for each stepper motor, but that didn't work. Repetier, thank you, too. M84 did not change anything. Motors are still on and energized after…

  in All motors energized but not moving at all Comment by Buttons April 2018
• Here's my FW configuration: https://i.imgur.com/F2hQQ4y.png (external image because of size)

  in All motors energized but not moving at all Comment by Buttons April 2018